Home > Hp Error > Hp Error Code 10.0002

Hp Error Code 10.0002

Ready Control Panel Message The control panel reads Ready . A broken tooth on one gear is all it takes. Reply With Quote 01-03-2010,09:47 PM #2 cs_steve View Profile View Forum Posts View Blog Entries View Articles Super Moderator Join Date Dec 2006 Posts 700 Generally that memory supply error has The following table lists the available status/control panel status messages for the HP Color LaserJet 1600 printer. http://upintheaether.com/hp-error/hp-error-code-24-10.php

Override in use Unauthorized black Unauthorized cyan Unauthorized magenta Unauthorized yellow Unauthorized supply in use Alert messages Door open Jam in cartridge area Jam in output bin - duplex area Jam This is a continuable error state. Attention Light Generally, the Attention light blinks when the printer is out of paper, when a jam has occurred, or when other problems that need attention occur. top Install cyan cartridge Error message Install cyan cartridge alternates with (gas gauge) with a ? https://h30434.www3.hp.com/t5/LaserJet-Printing/changed-toners-received-a-message-10-0002-supply-error/td-p/834217

Recently it has been having problems with its memory dimm as well. Reply With Quote 01-04-2010,11:45 PM #3 woodss View Profile View Forum Posts View Blog Entries Visit Homepage View Articles Senior Member Join Date Aug 2004 Location Victoria, Australia Posts 228 i Error 10.32.00 Unauthorized Supply Alternates with for help press "?" - A new non-HP supply has been installed this message continues until you press the check button or install an HP

Reinstall the print cartridge. The user must acknowledge the message by pressing the SELECT button. These can be set within the Remote Control Panel. Action Reinstall the black print cartridge.

Jam in print paper path - registration area Error message Jam in print paper path alternates with Open door and clear jam Description A paper jam has occurred in the registration The following message types are available: Initialization and Ready messages Supplies messages Alert messages Warning messages Critical error messages Status messages Printing reports and documents messages top Initialization and Ready messages If not replace the motor or drive circuit as required. http://h30434.www3.hp.com/t5/LaserJet-Printing/10-0001-Supply-Memory-Error/td-p/4849463 The supplies gauge will display the consumption levels of print cartridges.

First Time Here? Look for the conductive contacts on the cartridge and the corresponding contacts in the printer and make sure they are clean and free of contaminants. The device has experienced an internal hardware error. NOTE: If this error occurs upon initial power-up on the printer, remove all cartridges to check for the orange packing tape.

Also inspect the black plastic on e-label reader to ensure it is not bent or broken. If the problem continues, contact HP Customer Support Center for technical assistance at http://www.hp.com/support/clj2600n or see the flyer that came in the printer box for additional contact information. 54.16 Error Turn Inspect the print cartridge to ensure the e-label reader is attached to print cartridge and is not damaged. If a surge protector is being used, remove it.

ERROR 43 / ERROR 43 OPT INTERFACE This indicates a communication problem between the formatter PCA and an optional interface installed (such as a network card). weblink Job output might be affected. This message is a Ready State with Warning error; it does not require the user to take action. Action Load the paper into the specified paper tray and press the (SELECT) button on the control panel to complete the duplex print job.

If the board becomes defective, you will receive an error 12. You can depress these by hand and hear them click. We see a lot of this error. http://upintheaether.com/hp-error/hp-error-code-54-2.php Power cycle the printer.

You may have to register before you can post: click the register link above to proceed. Inspect the print cartridge to ensure the e-label reader is attached to print cartridge and is not damaged. Power cycle the device.

Control Panel Message The control panel reads Hewlett Packard.

If this does not clear the error, replace the fuser. 50.2 Fuser Error Turn off then on 50.2 Slow fuser error The device has experienced an internal hardware error. If reinstalling the print cartridge does not resolve the issue, replace the print cartridge. Action Configure the printer for the correct paper tray and type. Black, Yellow, Cyan, and Magenta Supplies Status gauges A ?

The user must acknowledge the message by pressing the SELECT button. Find Solutions, ask questions, and share advice with other HP product owners. The following message types are available: Initialization and Ready messages Supplies messages Alert messages Warning messages Critical error messages Status messages Printing reports and documents messages Initialization and Ready messages The his comment is here NVRAM initialization (power on with Select and Cancel buttons pressed and held Intitializing . . .

Remove all EIO devices and firmware DIMM if installed. Cleaning . . . This is a continuable error state. If the problem continues, contact HP Customer Support Center for technical assistance at http://www.hp.com/support/clj2600n or see the flyer that came in the printer box for additional contact information. 50.9 Fuser Error

Thank you and your firm again, you were terrific. Override in use Error message Replace supply. San Rafael, CA Great that you have that part in stock and thank you for your quick reply. Plug the device directly into the wall socket.

A Demo page can be printed by pressing the (LEFT ARROW) and (RIGHT ARROW) buttons simultaneously. under the missing yellow gas gauge. Any printer repair required as a result of using a non-HP or unauthorized supply is not covered under warranty. Figure : Example of an E-label on the print cartridge Using the lint-free cloth, wipe the metal contacts on the end of the print cartridge.

Is the software set for the size you're using? Load Tray 1 Error message Load Tray 1 alternates with Press to use available media Description The printer is processing job, but no trays match. Click here to view the document "HP Color LaserJet 2600n - Calibrating the printer" available on the HP Web site at (http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=c00314525). Click Start, Programs or All Programs (Microsoft Windows XP or Microsoft Windows Server 2003), HP, HP Color LaserJet 2600n, and then HP Color LaserJet 2600n toolbox from the Microsoft Windows desktop.

If printing is continued after the supply is empty, damage to the printer can occur. Click Order Supplies, to order supplies online. If a surge protector is being used, remove it. If the problem continues, contact HP Customer Support Center for technical assistance at http://www.hp.com/support/clj2600n or see the flyer that came in the printer box for additional contact information. 54.13 Error message

Also check motor cable connections.