Hp Error 58.2
Measuring a thermistor gave 10.8 kilo-ohms at 23 centigrade changing very rapidly when I touched it with my finger to stabilise at 8.86 kilo-ohms. However it's not a very likely fault, so it might be worth considering some other factors first. Amazon, the Amazon logo, Endless, and the Endless logo are trademarks of Amazon.com, Inc. HP's service manual says: The environmental sensor (TH3) has experienced an error.
We don't sell hard drives, monitors, software, mp3 players, or the zillions of other computer products sold by every other cookie-cutter website. I decided to look it up to see how popular it is before I wrote about it and there seems to be some controversy over this error. Kevin Find additional printer service tips, manuals, and parts diagrams at: http://www.lbrty.com/resources.html/Additional Printer Repair Articles can be found at : http://www.metrofuser.com/ Related posts:51.10 Printer Error - HP Laserjet 4200, 4250, 4300, Replace the engine controller board. 5. http://printerrepairsupport.com/58-2-printer-error-hp-4240-4250-4350/
A paper tray lift malfunction. 2. X description: 4 = Printer fan 7 = Duplex fan 1. Replace the DC controller. 52.X PRINTER ERROR The laser scanner speed is incorrect. NM..
After thinking more about it, I believe it could be both. Replace try one input unite. If the message persists, reseat the fuser. It probably doesn't happen much.
If that does not work, replace the fuser. It's easy to get to, reseat, and replace. Pull the cover straight back and away from the printer.Top cover 1. http://www.advancedlaser-hp-error-codes.com/error_58.htm HP LASERJET 4300 ERROR 50.1 Q: Our hp laserjet 4300 has a fuser error 50.1 on the display panel. The printer was running fine the day before and the next morning
A memory tag error was detected.2. The leads are actually heading into the DC-controller. You can even send us your printer for repair. A D.C.
It works if I dont put in the 2 screws on the right side. http://www.fixyourownprinter.com/posts/51650 Reseat cables to the laser/ scanner and engine controller. 4. It says 58.2 is the air-temperature sensor. Thank you.
Air temperature sensor error.2. HP LASER PRINTER 8100, 8150 ERROR 58.1, 58.2, 58.3, 58.4 1. Check and reseat the fuser and toner cartridge to make sure they are not hindering gear movement in the drive train. 3. Again the service manual is not very good at relating this information.
The line voltage and current source at the printer location might need to be inspected to ensure that it meets the printer’s electrical specifications. 55.xx PRINTER ERROR alternates with CYCLE POWER If not, then you need to replace the air temperature sensor. Change tray 1 input unite. 3. X description: 1 = Beam-detect error 2 = Laser error 1.
The whole PIU (pickup assembly) is held in by 4 screws in the front and it slides out. Remove the top accessory cover. 2. Trying a few other formulations was no better Remarks We rather suspect that this error is there because it has to be possible for the environment sensor to fail or be
Replace the engine power supply. 6.
This content is provided “AS IS” and is subject to change or removal at any time. If you have found the information useful and possibly saved you a service call, a donation would go a long way in keeping the articles coming and help my family understand I would test the wall outlet or have building maintenance do it for you. Replace the power supply.
Defective D.C. Disconnect and then reconnect the wire and see if that makes a difference. In all probability the printer has been badly placed so the sensor has been driven too hot or cold. Improperly fitted fan cable. 2.
Replace the DC controller PCA. 7. All Rights Reserved. Try the DIMM in another slot. (The firmware DIMM must remain in slot #4—the lowest DIMM slot.) 3. HP LASER PRINTER 4345MFP, 5025MFP, 5035MFP ERROR 58.X 1.
A: HP laserjet 4250 error 60.02 are caused by the lifter motor not properly lifting the tray 2 cassette. This can be caused either by a faulty tray 2 cassette or Indicates that the paper diverter inside the right upper door is out of position, causing an error feeding media from tray 1. 2. A power supply error code.2. The page containing the error will automatically be reprinted. 1.