Home > Hp Error > Hp Error 020011

Hp Error 020011

Printer continuously rejects Printheads Clean Printhead and Carriage flex contacts. Replace Carriage Assembly. Turn the printer on and retry function. Replace the Refill Assembly.

top System error 080001 Explanation Hard disk installed without PostScript. Check that the Elevator Stepper Motor is NOT shorted. Open the top cover. If the error reappears, contact HP support. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c00010030

Recommended Action Turn the printer off, then on. System error 010024 Explanation Problem initializing the encoder pulse generator. top System error 020002 Explanation Error in finding the refill arm home position.

Make sure the MIO card is installed correctly and switch the printer ON again. System error 010032 00000xx Explanation Fan test failed. Replace Trailing Cable. If "D0105 Fail" - Check if Line Sensor is installed/connected correctly.

Printheads Check Purpose - Check that the Nozzles of the Printheads are functioning correctly. If the error reappears, contact HP support . If the error reappears, contact HP support. http://support.hp.com/us-en/document/c00010030 Recommended Action Turn the printer off, then on.

System Error: 07xxxx - Firmware Error. Create your Spare Parts List. top System error 050000 Explanation The line sensor has problems finding the mark encoder. System error 020001 Explanation Elevator position not found.

Check the media path and clear it if necessary. You can add, delete list items and change the quantity of spare parts. Remove and reinstall as needed. Recommended Action Turn the printer off, then on.

System error 010030 Explanation One of the interconnect boards not detected. Recommended Action Turn the printer off, then on. During initialization another error code will appear. HP Designjet CP Series Printers - System Errors, Explanations, and Actions System error 0000D8 XXXXXXX System error 010020 System error 010021 System error 010022 System error 010023 System error 010024 System

Open the top cover. WINDOW MUST CLOSED BEFORE YOU PERFORM THIS CALIBRATION. Use the following keys to adjust the swaths counter. • Up Arrow - Increase the Counter Digit. • Down Arrow - Decrease the Counter Digit. • Enter - Select the Next top System error 010101 Explanation An action outside of the EEROM limits has been performed.

Replace Y-axis belt. Change the contents of the old list and save it as new. Remove the Drive Roller and install in the correct position. "Switch Power Off / Check Printhead Path" message appears when the Printer is about to cut or is cutting?

If problems persist, contact HP support .

If instructed to install the ink cartridges, install the cartridges and verify printer functionality by printing several internal prints. Check if the Media used is suitable for the printer. Insure that at least 4 MB or memory is installed: Turn the printer off, and unplug the power cable. Replace Refill Interconnect PCA.

Figure : Rubber tab on left side of the overdrive assembly (HP Designjet 750c pictured) If the tab was re-positioned in the previous step, turn the printer on and attempt to If the error reappears, contact HP support. If the error reappears, contact HP support . Recommended Action Turn the printer off using the power switch on the back of the printer.

If the error reappears, contact HP support . Before installing each Printhead, check the continuity of all four Printheads. Figure : Rubber tab on left side of the overdrive assembly (HP Designjet 750c pictured) If the tab was re-positioned in the previous step, turn the printer on and attempt to System Error: 020002 - Check/replace Refill Interconnect Cable.

Replace Electronics Module. If "D0100 OK" - Test Passed. Use saved Parts Lists as templates to create new lists. Perform the Printhead Continuity Test.

Adjust the Swaths Counter (####) after replacing the Electronics Module. If you have not installed a new Electronics Module, current font type will be displayed. Replace Y-axis Motor Assembly. • If Faulty X-axis Motor - Replace X-axis Motor Assembly . • If both DC Motors fail, replace Electronics Module. Contact HP?

You can print your Parts List or export to Excel to further work with him. Turn the printer off and then on (without cartridges installed). Check that the Service Station stepper motors are NOT shorted. Calibrations Entering the Service Calibrations Menu System 1 Hold the UP and ENTER keys down and switch printer ON from the power switch on the back of the printer.

If "C06xx Fail" - If the calibration pattern is bad, try recovering printheads using the front-panel menu and try the calibration again.