Hp System Error 86 01
Another thing is what you want to do is move the carriage assembly by using the belt itself and not pushing and pulling on the acutal carriage. align printhead by unknown on Nov 27, 2012 at 6:22pm Add comment Please sign in to comment 0 error 86:01possibly paper jam1. Learn How to Post and More  Community News  Best of the Community Blog  Notebooks Notebook Operating System and Recovery  Notebook Boot and Lockup  Notebook Wireless and Networking  Notebook Audio  Notebook Video, Load media into the printer. http://upintheaether.com/hp-designjet/hp-system-error-05-10.php
I unlocked the carriage and tried moving it from side to side. clear paper path4. I started off with the 21:10 error. If the issue persists following the steps below, generate a CSO for service. https://h20565.www2.hp.com/hpsc/doc/public/display?sp4ts.oid=3204979&docId=emr_na-c04581797&docLocale=en_US
Hp Designjet 800 System Error 86 01
Turn the printer on, see if the error goes away. Also I have looked into the troubleshooting guides. You have a problem with the cover that secures the printheads in the carriage assembly. General causes are media or other obstructions in the carriage path, the trailing cable, worn carriage bushings, lack of lubrication in the carriage path, a dirty encoder strip, the scan-axis motor,
Move the carriage manually through the entire movement path to see if it encounters any obstructions or has more resistance in any particular spot. by dlstoehner on Jun 19, 2014 at 8:07am Add comment Please sign in to comment Please sign in to comment HP DeskJet 500 Buy discount ink Buy this printer More HP then the carriage goes back to the service station then the error pops up...
Using a lint free cloth dampened with water, clean the trailing cable and the underside of the printer frame that holds the ink-tube system.
im learning a lot :) by Dup34 on Jan 13, 2012 at 5:57am Add comment Please sign in to comment 0 TRIED TO FIX THE ISSUE BUT IN LAST FOUND COLLAR Hp Designjet 500 Replacement Belt Turn the printer off and replace the Carriage and Trailing cable (refer to pages 8-78 and 8-40 of the Service Manual). by dmzcompute on Mar 20, 2013 at 3:53pm Add comment Please sign in to comment 0 plotter startup time (service station proper moment)carraige moment time display showing 86:01 error. align printheadHP DESIGNJET50042" also , jetdirect 620n not detecting.
Hp Designjet 500 System Error 81:01
Just got this designjet 800 from a guy that lost the lid cover of the carriage (blue part LOL) and didn't want to by the whole carriage just for that part have a peek at these guys Solution 1: If this error code appeared but was not caused by a paper jam, then try the following: Enter the Printer Information and check the Scan-Axis usage. And it's getting confused by the splatter. Slide the carriage manually back and forth several times to evenly spread the lubrication across the entire carriage rail. 86.01 Possible Paper Jam
If yes: place the rod back into its socket and reinstall it back into the system. Turn the printer on and attempt to verify functionality. Is the WD40 an OK lube? check over here switch power on5.
I'll inspect the belts for any junk & report back.I did turn off the cutter, but the printer insists on using the cutter to trim the end of the paper roll Hp Designjet 500 Error Codes In this case replace theService Station/Aerosol Fan Assembly ⇒ Page 8-52.� Perform the Carriage Movement test ⇒ Page 4-8. Now the cover could be broken and is hitting the side as the carriage moves over the service station.
If replaced, attempt to verify functionality before continuing with the remaining steps.
by malvin on Apr 24, 2006 at 1:26pm Add comment Please sign in to comment 0 I do not usually work on 500 series, but with most plotters when there is Should the plastic on the encoder strip be facing me or is it against the plotter? Parts and diagrams can be obtained at partsurfer.hp.com. Hp Designjet 500 Service Manual Printers problem solving,tips, tricks and tutorial.
I figure there is a very good chance I have put something back together wrong and that is why the error message. Maybe I have put something back in backwards. Share Flag This conversation is currently closed to new comments. 3 total posts (Page 1 of 1) + Follow this Discussion · | Thread display: Collapse - | Expand + this content Solution 3: Verify the Service Station Take out the service station and make sure it run through its full range of motion by rotating the motor spindle.
by unknown on Jun 28, 2013 at 5:56am Add comment Please sign in to comment 0 Did you bother to read the posts above yours.