Home > Hp Designjet > Hp System Error 05 10

Hp System Error 05 10

Contents

You found the best solution though. Then plotter was showing 00:01 error for some reasons.After I reboot plotter it boots up as DJ 500, the warning 05:10 disappear,plotter not asking any more about formatter. Press in the thumb-tab on the side furthest from the edge that has the cable-hole. top System error 06:03 (only applicable for Designjet 800 series) Explanation Hard disk error on the formatter verify functionality of the machine by removing the formatter, continue past the system error weblink

HP Customer Support Support Home Products Software and Drivers Forums Contact Support Search Select your Model Let HP find my products Identify now HP can identify most HP products and recommend top System error 04:11 Explanation Jetdirect network card not detected. Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎12-23-2013 12:00 PM I found the way how to get around 05:10 Reinstall the accessory card cover. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c00993566

Hp Designjet 800 Formatter Card

Open the top cover. If not, check functionality. 9. The maximum length has been extended to 255 characters for an IP address and to 47 for an IPX address.

If the problem persists, click on Support at the top of the page for additional HP support and contact options. NOTE: This error code only appears in HP Designjet 800 series, or in the Designjet 500 series printers with HP-GL/2 cards installed. Recommended action Turn the printer off and allow a few minutes for printer to cool. Hp Designjet 500 Error 79 04 In a few minutes the printer will print the Service Print.

Unfortunately my plotter do not have MODEL NUMBER option. Hp Designjet 800 Hard Drive Image If the error re-appears, re-create the file and try printing again. Swivel the cover in the direction opposite to the embossed arrow and clip the other two tabs on the opposite side into their slots. Z7_3054ICK0KGTE30AQO5O3KA30H5 hp-country-locator-portlet Actions ${title} Loading...

If the file is binary, use AppleTalk to send the file to the printer. Hp Designjet 510 Error 05 10 Remove the LAN card. If the problem continues, try processing the file in the PC instead of the printer (select Avoid out of memory in the Advanced options in the Printer Driver) top System error Recommended action If the problem persists, click on Support at the top of the page for additional HP support and contact options.

Hp Designjet 800 Hard Drive Image

If yellow light is not flashing, it indicates that the HP-GL/2 Accessory Card has failed. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c01917223 Hold and key and power up plotter. Hp Designjet 800 Formatter Card Turn on the printer, following initialization re-send the file that generated the error. Hp Designjet 500 Error Codes top System error 43:10 Explanation A problem has occurred with the Vacuum fan.

A.02.08, which fixes the issue. have a peek at these guys Turn the printer on and attempt to verify functionality. NOTE: If Removal and Installation instructions are needed for reference during any repairs performed, refer to the HP Designjet 500 and 800 Series Service Manual available on the Computer Care Web Turn the printer on and attempt to verify functionality. Hp Designjet 510 Error Codes

top System error 05:09 (only applicable for Designjet 500 series) Explanation Formatter installed instead of HP-GL/2 accessory card. The root cause was the combination of hostname (printer name) and domain name exceeding 31 characters. By using this site, you accept the Terms of Use and Rules of Participation IBM WebSphere Portal Home IBM Logo Sign Up Log In Welcome Getting Started Contact HP - http://upintheaether.com/hp-designjet/hp-system-error-86-01.php CAUTION: HP offers no technical support for persons who are not qualified to provide HP Warranty repairs.Example: Replacing the Trailing Cable on any Designjet Printer is not a user service.

top System error 02:13 Explanation A problem has occurred with the carriage assembly. Hp Designjet 500 System Error 81 01 Modify your browser's settings to allow Javascript to execute. Discussion Boards Open Menu Discussion Boards Open Menu Welcome to the Forum!

Formatter/gl2 card was bad.

Solution: replace the formatter Recommended action Turn the printer off and unplug the power cable from the back of the printer. If AppleTalk is not being used to send the binary file to the printer, change the printer's internal PostScript settings to Binary (Set-up menu, PS settings, Encoding, Binary). b. Hp Designjet 500 Firmware Update Download Open the carriage cover and remove all printheads.

Any slot is suitable for any card. 10. Carefully remove the plastic cover from the left-hand back of the printer by unclipping it. DO NOT attempt to verify functionality by sending files from the computer as the printer (Designjet 510 and Designjet 800) WILL NOT be able to process it without the card. this content First Time Here?

If the problem persists, click on Support at the top of the page for additional HP support and contact options. Using the flat ended screwdriver, gently tighten the screws until the card is secure. If the problem persists, click on Support at the top of the page for additional HP support and contact options. top System error 01:10 Explanation A problem with the Electronics module has occurred.

Removed and just cleared the error warning by hittingthe ok button. Go to SERVICE UTILITIES3. Thanks. Refer to the Service Manual (pages 8-24 through 8-26 and pages 8-5 and 8-6) for instructions.

The Aerosol Fan has reached its maximum current limit. You can use a screwdriver or do it manually. Allow printer to complete initialization. Install the Accessory Card in the other slot (where the LAN card is, or would be located).

Follow the instructions below to help solve the issue: Turn the printer off. Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎11-06-2015 12:12 PM Hi,The best you can do is set the printer Turn the printer on and attempt to verify functionality. Recommended action Turn the printer off and allow a few minutes for printer to cool.

If the problem persists, click on Support at the top of the page for additional HP support and contact options. If the problem persists, click on Support at the top of the page for additional HP support and contact options. Once functionality has been verified, turn off the printer and unplug it. 6. It that easy!!!!Now we have 3 working plotters ready for new home.

Follow the on-screen instructions to save the file to your computer. top System error 21:11 Explanation A problem has been detected with the Service Station assembly. Highlight Printer Information in the printer's Setup menu and press the Enter key.