Home > Hp Designjet > Hp Plotter Printhead Error

Hp Plotter Printhead Error

Contents

If the error message continues, replace the printhead. When it is finished starting up, when prompted, press the OK button, and proceed to install the printheads. At this point in time, I have a fix: I use an old G4 PowerMac running OS 10.4 connected to the HP 90 via network card to run the HP Utility. Last of all, service may be required (including new Ink Cartridges) to replace the SRK Tubes. his comment is here

Here's the link. The diagnostic codes did not indicate a sensor problem at all. I determined the Light Cyan head was at fault and ordered a replacement. It's available on the HP site.

Hp Designjet 500 Printhead Cleaning

About the same price as a new printhead.Installed it and had worked great ever since.-- hide signature -- Skip Teschendorf Reply Reply with quote Complain colourgeek • Veteran Member However, you can do everything that's needed using the three buttons on the control panel by referring to this document. Printhead replacement will fail even if the ink level is low like less than 10%. If the message still continues to appear, contact HP support.

Make sure the printer is plugged in and the power is turned on. No point in running it if not needed. Remove all the printheads. Hp Designjet 500 Printhead Alignment Error I have the identical issue and couldn't find a cure.

NOTE: If the product does not beep when you insert the printhead and the Replace message appears on the Touch Control Panel display, the printhead may need to be reinserted. Luckily for me, there was one available in my area, so I was able to check it out before I purchased it. Update - 4/2009: Another head gave out - the banding in cells C2, D1 and D2 pointing to a faulty Light Magenta printhead. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpp03052 This is one man's story.

One time I was told by a tech, "If I need the prints so badly I should have bought one of their better printers." I was fuming. Hp 11 Printhead The service call to HP was $39.95 + Tax, but as I said, they sent me a new printhead overnight free of charge. I now have no fingerprints, a status that equips me for a life of crime. The Touch Control Panel display confirms that all printheads are correctly inserted.

Hp Designjet 500 Printhead Replacement

I've done Epson and I've done HP. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c01738264 It's nice to have HP's good diagnostic tools, even if the instructions are so poor. Hp Designjet 500 Printhead Cleaning If the message continues to appear after cleaning the Ink Supply Station, replace the Ink cartridge again. Hp Designjet 500 Printhead Set Reto says: March 12, 2012 at 4:00 am Hello, i am having the same problems.

I was worried that I had air or dried ink in the lines, but the tech said if the printhead didn't correct the problem I should call back and he would http://upintheaether.com/hp-designjet/hp-plotter-error-6105.php Everything I have tried to print for the last few days has come out with a reddish/pink hue. Don't make my mistake and let the ink dry on your fingers. Don't even think of calling HP for help. Hp Designjet 510 Printhead Replacement

I was sent a new head overnight at no additional charge. I finally received the ink tube assembly from China and installed it successfully. Then, holding the Power button down I pressed the Cancel button twice to force a ‘Soft' Printhead Recovery (HP speak for flushing the heads). weblink The process will take about five minutes.

If the message continues to appear, turn the Printer off and clean the electrical contacts inside the Ink Supply Station. Hp Designjet System Maintenance Utility Press on the information icon. R&D has quietly continued with dye, and the 130 series is in no way a throw away product.

The printhead is fine, but the error condition is being triggered by a different problem that is not being detected and differentiated.

The product number of the printhead. A first print test showed a repeat of the problem (the print was as sharp as can be) but after a second cleaning the problem persisted. At least you told us how to use the confounded control panel. Hp 11 Printhead Cleaning Figure 12: Removing the printhead Pull the blue handle upward until the printhead is released from the carriage.

My dj130 is working fine. The current warranty status of the printhead. If some residue remains, slightly moisten the cloth with distilled, filtered, or bottled water and continue wiping until the contacts are clean. check over here I have also extensively annotated one of the illustrations below and provided a click-through to an HP print quality document which helps with diagnosis of printing problems.

After it is complete, the printer will prompt Ready. It's a simple fix to clean it, but this little sensor caused me many hours of confusion and grief!! Open the main window and open the carriage clamp, then remove all eight printheads. You can use a roll that is at least 610 mm (24 in) wide or a cut sheet that is A2 landscape or larger.

Pull the power cord now, then remove all the heads. Now all was well. CAUTION: Do not wipe the actual nozzle plate on the printheads as doing so can cause damage to the printhead. After changing the print head it is necessary to run the HP System Maintenance->Calibrate Color utility for each type of paper you propose using.

Interpreting test print results is addressed in this very poorly written document on HP's site. First, they will charge you for fixing their errors and second, the chances of finding someone who has the answer is slim to none. Once Apple's OS X Tiger (10.4.x) was introduced HP failed to properly update its System Maintenance Utility for Mac OS X, meaning that when you fire it up you will get When the printer is at a Ready state, open the cartridge and printhead access door on the right-side of the printer.

Figure 2: Printhead tape removal Gather the appropriate cleaning materials: Any clean, soft, lint-free material that will not come apart or leave fibers behind when wet (coffee filters work well) Enough Yes HP is a poor company on support but the printers are really great. Chris says: January 10, 2011 at 10:41 pm TomsWell, yes, there is a new utility. Figure 15: Inserting the new printhead Push down as indicated by the arrow shown below.