Home > Hp Designjet > Hp Plotter Error 86 01

Hp Plotter Error 86 01

Contents

Some times the cable will catch bad enough to shut the carriage axis down which is why it is stopping. So the head is stopping due to something else than the cutter impeding the head's movement. When I plug the unit into power this is what happens.  (note, I have sent a video via wetransfer.com showing the startup) Carriage travels to left and touches the cutter.  The Wenn du bei YouTube angemeldet bist, kannst du dieses Video zu einer Playlist hinzufügen. navigate here

by malvin on Apr 24, 2006 at 2:14pm Add comment Please sign in to comment 0 When the belt is starting to go you usually get shutdowns every once in the Visually check for jammed media or other obstructions in the carriage path and remove any obstructions found (remove any loaded media as well). Open the window and you can manually depress it by inserting a tip of a screw driver on the black sensor actuator. If firmware is lower than A.02.04, download the newest available firmware before continuing with the remainder of this document.

Hp Designjet 800 System Error 86 01

I can easily move the cutter across the paper and trim the paper with almost no effort at all. Cleaned the Encoder tape/ribbon with soft cloth. Diese Funktion ist zurzeit nicht verfügbar. NOTE: If the carriage will not move out from the service station, create a CSO for service (send ALL required parts as listed below).

Specifically, it is normal to hear a slight clicking noise when the carriage moves under the left or the right-hand covers. Reply 0 0 jasonmiamifl Grad Student Posts: 342 Member Since: ‎09-18-2010 Message 4 of 6 (14,345 Views) Report Inappropriate Content Re: HP DesignJet 500 Error 86:01 when trying to trim sheet General causes are media or other obstructions in the carriage path, the trailing cable, worn carriage bushings, lack of lubrication in the carriage path, a dirty encoder strip, the scan-axis motor, Hp Designjet 500 Severe Error 0x8010003 Using a lint free cloth dampened with water, clean the trailing cable and the underside of the printer frame that holds the ink-tube system.

by dmzcompute on Apr 24, 2006 at 2:07pm Add comment Please sign in to comment 0 Hmm, come to think of it, pushing/pulling the carriage does feel a bit stiff...I overlooked Hp Designjet 500 System Error 81:01 Turn the printer on. Vacuumed out the service bay area.

Wird geladen... Über YouTube Presse Urheberrecht YouTuber Werbung Entwickler +YouTube Nutzungsbedingungen Datenschutz Richtlinien und Sicherheit Feedback senden Probier mal was Neues aus!

Nächstes Video HP Design Jet 500 Printer Service Station Maintenance Part 1 - Dauer: 8:18 rronmar 23.554 Aufrufe 8:18 HP Designjet 500, 800 Belt Replacement & Calibration - Dauer: 38:05 Bob Hp Designjet T1100 86:01 Error Attempt to verify functionality, if problems persist, continue with the remaining steps. by nivek on Jun 6, 2011 at 9:56am Add comment Please sign in to comment 0 thx in advance,problem has been solved by nevek help.thanks again. Search Search for: Follow UsMy Tweets Blog at WordPress.com. The TWI Designjet Documents library presented here as a courtesy of ComputerCareOnline.com The owners of this website have no affiliation to

Hp Designjet 500 System Error 81:01

Learn more You're viewing YouTube in German. http://www.fixyourownprinter.com/posts/37933 You can change this preference below. Hp Designjet 800 System Error 86 01 Let me tell you what i did; A few days ago i replaced the belt, well it looks like i had the data strip or whatever you call that part on Hp Designjet 500 Paper Jam Error La correa debe cambiarse siempre que llege al final de su ciclo de vida útil, el no hacerlo puede provocar daños aún mayores.

If I manually move the cutter to the center of the axis and then turn the printer on, the print head moves to the left and pushes the cutter completely back check over here For me, I believe it is due to two little 3/4 circle clips that fit into the carriage assembly and onto the sliding rod. Turns out it has lots of little black lines running across it vertically. Wird geladen... 86.01 Possible Paper Jam

Respond to this 0 I found this guide on HP's website that may be useful to you.The 86.01 is a carriage movement failure. Die Bewertungsfunktion ist nach Ausleihen des Videos verfügbar. Any suggestions by unknown on Nov 16, 2012 at 2:52pm Add comment Please sign in to comment 0 error 86:01possibly paper jam1. his comment is here Carriage returns to the service bay and then backs out to left.

CAUTION: Ensure the printer is turned off and unpluged from the power source before continuing with Step 3 below. Hp Designjet 500 Replacement Belt In this case replace theService Station/Aerosol Fan Assembly ⇒ Page 8-52.� Perform the Carriage Movement test ⇒ Page 4-8. Release the carriage as instructed in Steps 6a - 6e in the "Contact center agents" section listed above.

Established in 1900, The John E Wright group specialize in the supply and installation of large format HP printing and plotting solutions; CAD and graphic systems, RIP software solutions, printing media

From the main front-panel menu, select the Ink menu and press Enter. align printheadHP DESIGNJET50042" also , jetdirect 620n not detecting. clear paper path4. Hp Designjet 500 Error Codes Solution 2: The Carriage is bumping into the Service Station.

Anyone know how to make these stay? Clean and lubricate the rail first. I'll inspect the belts for any junk & report back.I did turn off the cutter, but the printer insists on using the cutter to trim the end of the paper roll http://upintheaether.com/hp-designjet/hp-4500-plotter-error-79-04.php Reply 0 0 RngScottGus1 Top Student Posts: 5 Member Since: ‎11-26-2013 Message 5 of 6 (14,313 Views) Report Inappropriate Content Re: HP DesignJet 500 Error 86:01 when trying to trim sheet

Cleaned it and the error went away.Thanks, all, for your help!