Home > Hp Designjet > Hp Designjet Printer System Error 2

Hp Designjet Printer System Error 2

Contents

Recommended action Please call HP for technical support to troubleshoot the problem. If the error code continues, replace the yellow printhead. Additional workaround: Upgrade the printer's firmware (if upgrade is available). Action Replace the failing printhead using the following steps: Open the front hinged flap at the right of the printer. http://upintheaether.com/hp-designjet/hp-designjet-111-printer-system-error-2.php

This error indicates a communication problem. Please try the request again. Repeat the steps above for each ink cartridge that needs to be replaced. No printheads are shown if any cover is open or if the rear path is removed. http://h20565.www2.hp.com/hpsc/doc/public/display?sp4ts.oid=352387&docId=emr_na-bpp03841

Hp Designjet 130 Error Codes

Click here for information on contacting HP Customer Care. top System error 02:13 Explanation A problem has occurred with the carriage assembly. Before calling, please do the following: Review the following troubleshooting suggestions: Read the relevant driver documentation supplied with this printer (for users sending PostScript(R) files or those using Windows). Send an internal print to the printer to verify internal printer functionality: Load media into the printer (if not already loaded).

Remove the formatter card and re-install the formatter card. If the problem persists, call HP for technical support to troubleshoot the problem. top Cleaning the printheads Select the Help button from the driver software. Hp Designjet 110 Plus Error Codes Remove the protective tape from the printhead.

Was the information on this page helpful? NOTE: This error code may also be reported as a warning code, which will not prevent continued use of the printer. Click here for information on contacting HP Customer Care. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c01669949 If the file is binary, use AppleTalk to send the file to the printer.

If the error message persistss, check for a new release of the driver. Hp Designjet 110 Plus Manual Pdf Front panel buttons Power: Turns the mains power on and off. (The printer must be unplugged to completely isolate it from the power supply) Cancel: Cancels the current operation. Turn the printer on and attempt to verify functionality. Pull the latch forward and down to release the latch hook.

Hp Designjet 111 Error Codes

If all cartridges flash, there is an error in the ink system.

NOTE: Three sources of information are readily available to help you find an HP Support Services phone number: NOTE: 1. Hp Designjet 130 Error Codes Recommended action Turn the printer off and allow a few minutes for printer to cool. Hp Designjet 130 Error Icons Display panel icons The following table describes the icons found on the display panel of the printer.

Select your language if necessary, and then click the name of your operating system. his comment is here On: Normal. Figure 2: Printer Information page one top Understanding the front panel error code display System error codes are displayed on the printer's front panel, using the lit or flashing Ink Cartridge If the carriage is stuck at the right hand side of the Printer and cannot be moved out to the center of the Print Platen, likely it is because the Service Hp Designjet System Maintenance Tool

Click here for instructions on upgrading the printer's firmware . top System error 87:13 Explanation Unable to read the carriage encoder sensor. If the problem persists, click on Support at the top of the page for additional HP support and contact options. http://upintheaether.com/hp-designjet/hp-designjet-130nr-printer-system-error-2.php Allow printer to complete initialization.

Recommended action Please call HP for technical support to troubleshoot the problem. Hp Designjet T2500 Error Codes If the problem persists, click on Support at the top of the page for additional HP support and contact options. If the file is PostScript, check to see if it is binary.

Recommended action Follow the instructions below to help solve the issue: Turn the printer off and allow a few minutes for printer to cool.

Remove and re-seat the network card. Ink system error Remove all of the ink cartridges (see Step 2 above). The Front Panel will then move from showing the Primary Error code to the Secondary Error code. Hp Designjet 110 Plus Printing Problems If the problem persists, click on Support at the top of the page for additional HP support and contact options.

Recommended action Clean the electrical contacts on the cyan printhead. Off: Printer is powered off or is starting up. Open the carriage cover and remove all printheads. navigate here Icon Description Figure 1: Ink Cartridge icon NOTE: HP Designjet 120 and 130 printers will have six icons.

If the problem persists, click on Support at the top of the page for additional HP support and contact options. Recommended action Turn the printer off and allow a few minutes for printer to cool. A page listing all available downloads displays. top Clearing a paper jam Try pressing the CONTINUE button on the printer's front panel.

Please try the request again. If the error code continues, replace the cyan printhead. top Paper Jam icon Figure 7: Paper Jam icon Problem/error Paper is jammed or stalled, or a carriage is stalled. Recommended action Clean the printhead indicated by the printer.

Recommended action Upgrade the printer's firmware (if upgrade is available). Action Ink cartridge low or out Replace the depleted ink cartridge as soon as possible using the following steps: Open the front hinged flap at the right of the printer. Plug in the power cable again and check to see if the error code has disappeared. top System error 01:13 Explanation A problem with the Electronics module has occurred.

Was the information on this page helpful? top Paper Misaligned icon Figure 8: Paper Misaligned icon Problem/error The paper is misaligned and must be reloaded to print. Continue to use the site as normal if you're happy with this, or find out how to manage cookies I'm happy with that. Return the cartridges one by one to their locations, making sure that each is firmly seated in the proper position.

Click here for information on contacting HP Customer Care. If the error re-appears, upgrade the printer's firmware (if upgrade is available).