Home > Hp Designjet > Hp Designjet 750c Plus Error Codes

Hp Designjet 750c Plus Error Codes

As directed in dmzcompute's message dated 11/12/05 and a few messages before that as well.Thank you for not giving up on making it available. Page 239 C4705-90000 Parts and Diagrams 11-17... Page 102 Reassembling: Ensure that the bearing assembly at the right end of the drive roller is seated in the right sideplate and completely on the right side of the axial Page 70 Removing the Front Panel Assembly Front-panel 6-18 Removal and Replacement C4705-90000... this contact form

i actually did it a week ago) removed back cover (14 screws later) fuse on ps -fine, nothing looks burnt. Does anyone know what this means is wrong?Thanks in advance Steve by unknown on Aug 1, 2008 at 4:36pm Add comment Please sign in to comment 0 Hi Everybody!Is there any Remove and reseat, or install the Memory SIMM(s). Page 31 C4705-90000 Installation and Configuration...

Page 232 C4705-90000 11-10 Parts and Diagrams... Page 56 3/16 inch Removal and Replacement C4705-90000... That works until next time. Anyway if you get it into service mode there is a drop detect sensor test (not the calibration) run the TEST and stick something down the whole to see if it

I will tell you I recently was working on a 4200 troublshooting a noise in the feed assembly and shorted out the toner lid sensor with the frame. This is to ensure correct spacing between the drive roller and the cartridge nozzles. SERVICE TESTS 22 X Motion control REMOVE MEDIA PRESS ENTER The speed of the roller can be reduced or increased by pressing the appropriate arrow button. Tx 15 Reassembling: Ensure that the spittoon is properly attached to the Y axis motor holder and that it does not interact with the cartridge carriage.

Page 11 10 Product History and Service Notes 11 Parts and Diagrams 12 Support Services... by Anonymous on Jan 17, 2008 at 10:26am Add comment Please sign in to comment 0 Hi, I have been trying to find information regarding our HP Designjet 750c. If the error reappears, contact HP support . https://www.manualslib.com/manual/464727/Hp-Deskjet-750c-Plus.html Recommended Action Turn the printer off, then on.

Page 134 Error Code Problem Description Corrective Actions 070100 0000D8 XXXXXXXX 080001 8-16 Troubleshooting C4705-90000... by unknown on Nov 18, 2005 at 7:22am Add comment Please sign in to comment 0 Hi every body,I'm trying to download this manual "right click, save as" but I get The diverter bail bar assy. I've heard nothing good about Vista since it's been released.

So it doesnt have much to do with the carriage assembly. http://www.fixyourownprinter.com/posts/27330 Page 237 C4705-90000 Parts and Diagrams 11-15... Page 94 Removing the Service Station When performing this procedure, be careful to avoid staining your hands and clothing with ink deposited in the service station. Page 177 EEROM_PMAINT_RECVRY_K_1_OR_2_LOW 0x23 Number of at 1st or 2nd attempt success EEROM_PMAINT_RECVRY_K_1_OR_2_HIGH 0x24 recoveries. ( Black) EEROM_PMAINT_RECVRY_K_3_OR_4_LOW 0x25 Number of at 3rd or 4th attempt success recoveries.

Edge Detect Enter SERVICE TESTS 18 Edge detect Up Arrow Down Arrow If the value (###) of Sensor Reads is less than 100 when passing over the drive roller then the weblink You will need winzip in order to extract the zipped file. by Fudley on Jan 28, 2006 at 11:32am Add comment Please sign in to comment 0 can someone email me the instructions for installing the carriage belt by mccrackin on Feb top System error 060500 Explanation Line sensor not calibrated.

I recently purchased a HP 750C and would like to know if I can remove the base so that it will fit into my vehicle.Thanks by sphepburn on Mar 17, 2008 Page 247 C4705-90000 Parts and Diagrams 11-25... First make sure you have the setting correct for the type of media either roll or sheet. navigate here Recommended Action Install the latest version of the MIO card.

Page 132 Error Code Problem Description Corrective Actions 070000 H (where H is a hex digit Binary indicating value value Color which cartridge(s) failed) 750C 750C Plus 070005 offset value black Recommended Action Turn the printer off, then on. If functionality is verified, no additional parts should be replaced.

Page 142 4.

Then the erroror code 070020 Drop Detection error started. Turn the printer on and retry function. If problems were detected and rectified in the steps above test printer functionality. There is no loose scrap of media lying about as the plotter is now spotless.The lever operates fine, as does the carriage assembly.

Indicates dangerous voltage (terminals fed from the interior by voltage exceeding 1000 volts must also be marked). Page 156 Down Arrow 750C 750C Plus If the blk or clr false value (#) is less than 5 then press Enter. I have tried Smart Sniffer, but I must be using it wrong or something because it says nothing is happening as the computer detects the printer. his comment is here Turn the printer off and then on (without cartridges installed).

If you were going to sell it I would recomemend doing this and resetting the counter. Page 248 C4705-90000 11-26 Parts and Diagrams... As to the cutter check the position of the cutter after it cuts. Recommended Action Turn the printer off, then on.

Page 197 Bleeding 750C 750C Plus Description Causes Corrective Actions Feathering Description Causes Corrective Actions Migration (Black) Description Causes Print Quality 9-19 C4705-90000... Page 110 Reassembling: Position the bar cam between the left and right sideplates, or the lift mechanism will not work. Page 190 How do I select the print mode? I have never had any problems with it until today.

I am banging my hea against the wall here,lol. Run the diagnostic test first with the sensor blocked, then run the test with the sensor unblocked. by Lost in space on Feb 10, 2008 at 6:23am Add comment Please sign in to comment 0 I just got one and have the same problem as a previous user