Home > Hp Designjet > Hp Designjet 750c Plotter Printer System Error 060309

Hp Designjet 750c Plotter Printer System Error 060309

In the Service Test submenu, scroll to Test number 17. isn't shown. If it fails then either you can try and clean it out or replace the service station. Melde dich bei YouTube an, damit dein Feedback gezählt wird. Check This Out

Schließen Weitere Informationen View this message in English Du siehst YouTube auf Deutsch. The only way to tell is to take it apart.2. Copper lead was broken. Anmelden Teilen Mehr Melden Möchtest du dieses Video melden?

The best way to check the movement of the carriage assembly is to turn off the power and then you can move it by hand. Demos print fine. When I am able to plot I it will only plot one plot at a time. Press the PREVIOUS key until Ready appears on the front panel.

It's a little tricky it seems. I'm at work right now but I will post the full error code when I get home. by unknown on Aug 17, 2010 at 1:54am Add comment Please sign in to comment 0 carriage communication error. Download the drivers from the site http://h20000.www2.hp.com, then connect the plotter to the pc, install the drivers and switch on the plotter...and it is done?thanks a lot!

I used an old toothbrush and an exacto knife.8. Not sure how long really.Resetting (clearing) the EEROM. Thanks,Lon - Anonymous 0 MIO error. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c00010030 by ultrastructures on Oct 30, 2007 at 12:17pm Add comment Please sign in to comment 1 Has anyone had a problem where the plotter won't recognize the black ink cartridge.

oh, yes, pins on cartridge and carriage must be wery clean, (use 97\%alcohol), if you had old cartridges boiled them out or put them infront of thermal heater, so you can The BootP or DHCP server will configure the TCP/IP parameters on the HP Jetdirect. Plots are being clipped atthe front end of plot . Also the black did not appear to be printing smoothly.

I know they did on the 450.

Good luck and 2 sets of long needle nose & tiny flathead screw drivers.14. Blow out the ROM SIMM socket,3. Please retry your request.

Power off and unplug the cord for a few to several minutes. his comment is here You can change this preference below. Maybe the darn thing will tell you itself what's wrong with it:in front panel when states ready (well probably won't do that since states "cartridges missing." Again I'm a little rusty by dmzcompute on Oct 30, 2007 at 2:43pm Add comment Please sign in to comment 0 yes you're right!

Make sure that you carefully inspect the ribbon cable for bad/folded back foil contact ends. Look for the ink to start bleeding out noticeably or significantly, then give them a try. It worked great - thanks for the help, the plotter will live to see another day... this contact form You should be able to see how to engage the new belt with the carriage by looking from behind once the case is off.

The system returned: (22) Invalid argument The remote host or network may be down. by unknown on May 26, 2010 at 9:03am Add comment Please sign in to comment You should be able to turn off the cutter either in the front panel settings or Hit me an email if you need the service manual and I'll send it over to you.Good Luck by unknown on Jul 5, 2007 at 6:59pm Add comment Please sign in

If that's in place, not really sure what the problem is unless somehow your belt is outta spec.

Press the PREVIOUS key until Ready is displayed on the front panel. Thanks in advance. --jf by jf62 on Jul 18, 2006 at 2:10pm Add comment Please sign in to comment The instructions for replacing the belt involve disassembling virtually the entire plotter. by unknown on Jul 30, 2008 at 6:00pm Add comment Please sign in to comment 0 I just bought the hp design jet 750c plus used. Anmelden 6 0 Dieses Video gefällt dir nicht?

Tried unplugging it overnight. by unknown on May 24, 2011 at 9:45am Add comment Please sign in to comment Hi, Im a bit rusty on this machine. I have cleaned the encoder strip and the staggering of the lines has now gone away. navigate here Can some one let me know what is causing this error and how to best fix it ?

Return to TWI Documents Library Index Page HP Designjet 750C Plus Series Printers - System Error 070020 and 070030 In this document: Introduction Parts required (part numbers are subject to change) google HP 750 service manual by nivek on Aug 17, 2010 at 8:40pm Add comment Please sign in to comment 0 Wow you guys are fast. We shorted out the switch and it is still saying "Lower Window to Continue." I don't have a user manual, can you explain to me what you did to get beyond I think of 5 things; that narrows it down a lot, eh?:1.

Help is much appreciated, thank you. Is there a place I can find this info so I don't have to bother you guys by asking? Simultaneously press the ENTER and the UP ARROW buttons to access the Service Tests submenu. Hinzufügen Möchtest du dieses Video später noch einmal ansehen?

Thank you. Wipe clean the contacts on the firmware ROM SIMM,2. Learn more You're viewing YouTube in German. Check Carriage and Encoder interaction (the Carriage and Encoder should not touch each other).

by unknown on Nov 25, 2008 at 2:43pm Add comment Please sign in to comment HI Brian/ anyone else who can helpYou mention that you are running your designjet 750C on