Home > Hp Designjet > Hp Designjet 5500 System Error Codes

Hp Designjet 5500 System Error Codes

Contents

Recommended action Turn the printer off (using the main power switch on the back of the printer) and remove the network cable from the printer's network card. Unload the media and turn the printer off and back on using the main power switch at the back of the printer. top System Error 0A0030 (non-continuable) Explanation A problem in the Depressurizing Air system has occurred. The original capacity of the ink cartridge in milliliters. Check This Out

Click here for information on contacting HP Customer Care. Figure 9: Selecting a specific Printhead color The front panel displays the following information about the selected printhead (see Figure 10 below): The make of the printhead. If it still fails, report the error to the division. If the error code continues, replace the Main PCA Page 8-79. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpp03771

Hp Designjet 5500 Printhead Reseat Error

top System Error 0A0040 (non-continuable) Explanation Air Pressurization System (APS) failure. With the printhead icon highlighted, press ENTER. J7 and J8 SDRAM are memory DIMM slots. Corrective Action: Try the following: Make sure that the Ambient temperature is within the allowed range (between 0 and 55 Degrees Centigrade).

System Error: 0C00FF Problem Description: Print Mask could not be generated. If the Error Code reappears, then the Printer requires an on-site visit in order to resolve the problem. The program will proceed to upgrade the firmware. Hp Designjet 5500 Manual Pdf The front panel displays the following information on the selected ink cartridge (see Figure 5): The make of the ink cartridge.

Even if the error appears again, there is nothing wrong with the Printer. 20 Designjet 5000 / 5500 050000 error (Continuable) Lens has problems reading the Mark Encoder on the Drive Hp Designjet 5500 Service Manual If the error persists, call HP for technical support to troubleshoot the problem. If the error continues, call HP for technical support to troubleshoot the problem. useful reference WARNING Only replace one component at a time and check if the error has gone before replacing another component.

Open the cover on the back of the printer to access the ink cartridge assembly (right side of the printer, looking from the back). Hp Designjet 5500 Air In Tubes If functionality is verified, no additional parts should be replaced. The cause is not likely to be the Printhead because if it was, the Printhead would be marked as XX21 REPLACE. Press the UP or DOWNARROW key until the front panel highlights Printhead info.

Hp Designjet 5500 Service Manual

Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. Click here for information on contacting HP Customer Care. Hp Designjet 5500 Printhead Reseat Error top System Error 0B0006 (non-continuable) Explanation The Trailing cable has been incorrectly connected. Hp Designjet 1050c Error Codes Working...

top System Error 0D0000 (continuable) Explanation No Media Profiles available. his comment is here top System Error 0B0003 (non-continuable) Explanation ADCO Internal channels check failure. top System Error 0F0100 03180382 (non-continuable) Explanation The printer cannot deactivate the Cutter after cutting the media. Replace the APS Page 8-65. Hp 5500 Printhead Problems

Try the following (verify that the message returns OK after each step): 1. Click here for information on contacting HP Customer Care. Verify that the lens is clean and perform a lens maintenance procedure (instructions in Lens Maintenance kit shipped with the printer). 4. this contact form Scroll to Test Print and press Enter.

Recommended action Turn the printer off (using the power switch at the back of the printer), and check for obstructions in the Carriage path (Scan-axis) and remove if found. Hp Designjet 5000 Service Manual Press the TOP key (to return to the main menu). Click here for instructions on how to upgrade the printer's firmware .

The printhead warranty status.

If the error re-occurs or the problem persists, turn the printer off and continue with the remaining steps. Follow up: If you have an error code which is not documented in this Service Manual or you have an error which you cannot resolve, then report the error to the Check all the tubes of the APS and Tubes System and make sure they are correctly connected and are NOT pinched or damaged. Hp Designjet 5100 Error Codes top System Error 0C0040 (non-continuable) Explanation An Error has occurred in the Printhead Drop Detection.

When they start to degrade, the Printer will display (XX20) Recover, prompting the printhead recovery procedure (See Figure 11). There is nothing wrong with the Printer. Click here for information on contacting HP Customer Care. http://upintheaether.com/hp-designjet/hp-designjet-800-system-error-codes.php The error code should not appear again.

If the error appears, continue with the remaining steps. System Error: 01002D (Non-Continuable) Problem Description: The Main PCA cannot communicate with the Carriage. top System Error 010030 034c095e Explanation The power supply detects a low spike (e.g. If the error code continues, replace the PCA Page 8-79.

If the New Vacuum Fan does not function correctly either, then replace the Main PCA Page 8-79. Continuable and non-continuable error codes Some error codes are continuable, which means that it is possible to press ENTER on the front panel and continue working with the printer. Check that the Paper-Axis Motor cable is correctly connected. Corrective Action: Try the following: Check that the Paper-Axis Motor cable is NOT broken or damaged.

NOTE If the YYYY digits in the second set of 8 characters are zero [0000ZZZZ], this indicates a LAN Card System Error. Scroll to any of the selections and press Enter to start the print. Remove and re-install all six ink cartridges and press ENTER to continue.