Home > Hp Designjet > Hp Designjet 5500 Printer Error

Hp Designjet 5500 Printer Error

Contents

Quality, Productivity, or Max. Other operating systems NOTE: If the System Maintenance Utility has been downloaded correctly from www.Designjet.hp.com but problems arise while upgrading printer firmware via the System Maintenance Utility, another download is not Recommended action Press the ENTER key to continue operating. Click here for information on contacting HP Customer Care. http://upintheaether.com/hp-designjet/hp-designjet-5500-error.php

The mask generation algorithm could not generate the print mask. If the error re-appears, call HP for technical support to troubleshoot the problem. If the error continues, call HP for technical support to troubleshoot the problem. Click here for information on contacting HP Customer Care. read review

Hp Designjet 5500 Printer Manual

Attempt to verify functionality. Turn the printer on, if printer initialization completes (printer goes to a Ready state), continue with Step 6. If the error continues, call HP for technical support to troubleshoot the problem. Click here for information on contacting HP Customer Care.

Was the information on this page helpful? Click here for instructions on how to upgrade the printer's firmware . NOTE: In extreme circumstances, the printer may not recognize the new printhead because of build-up on the electrical connection between the printhead and the printhead Carriage. Hp Designjet 5500 Printhead Reseat Error Remove the DIMM access cover (four T-10 screws) from the back of the printer.

If the error continues, call HP for technical support to troubleshoot the problem. Hp Designjet 5500 Printer Driver Table 3: Printhead Information Status Numbers Error Description Procedure XX02 Reseat XX06 Reseat XX08 Reseat Continuity problem between the printhead and the Carriage Assembly Try each of the following (verify if Recommended action Turn the printer off, wait 15 seconds and turn the printer back on (using the power switch located on the back of the printer). Clean the Mark encoder (small slotted white plastic insert on the left end of the roller) using a lint free cloth lightly dampened with water.

Click here for instructions on how to upgrade the printer's firmware . Hp Designjet 5500 Price Click here for information on contacting HP Customer Care. Scroll to Replace Lens Cover and press Enter. If error appears frequently upgrade to firmware release A.02.xx 57 Designjet 5000 / 5500 0D0004 xxxxxxxx error (Non-Continuable) This is an internal general error code which can appear during the Printhead

Hp Designjet 5500 Printer Driver

If the error continues, call HP for technical support to troubleshoot the problem. If the problem persists following the upgrade, replace the lens cover: Scroll to the Printer Setup Options icon and press the Enter key. Hp Designjet 5500 Printer Manual If the error continues, call HP for technical support to troubleshoot the problem. Hp Designjet 5500 Error Codes Figure 3: Location of DIMM(s) NOTE: J6 - Boot ROM is internal printer firmware.

If the issue is unresolved, click here to contact HP support (http://thenew.hp.com/country/us/eng/contact_us.html) and provide the following information: Document number bpp03890 used for troubleshooting and a brief problem description to assist HP weblink Reseat or add memory (if needed). Scroll to Lens Maintenance, and press ENTER. Press the TOP key (to return to the main menu). Hp Designjet 5500 Error 1f50007

Even if the error appears again, there is nothing wrong with the printer 63 Designjet 5000 / 5500 0F0100 03180382 error (Non-Continable) After cutting the media, the Printer cannot deactivate the cutter 64 Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. If using the network card is not possible or acceptable, it is recommended that the parallel port setting in the PC BIOS be set to ECP mode (contact the PC vendor http://upintheaether.com/hp-designjet/hp-designjet-5500-error-messages.php top System Error 010091 (continuable) Explanation An error has occurred in the Paper-axis Motor Encoder.

If the error goes away, the issue is with the print server. Hp Designjet 5500 Specs Open the cover on the back of the printer to access the ink cartridge assembly (right side of the printer, looking from the back). Recommended action Press ENTER on the printer's front panel to continue.

Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on.

Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. Nächstes Video HP Designjet 5500ps Check Printhead Cleaner Path Error - Dauer: 2:36 Zeb Harris 14.385 Aufrufe 2:36 Designjet 5500 Belt Replacement & Calibration - Dauer: 29:55 Bob Wert 16.367 Aufrufe If the error persists, upgrade the printer firmware (if upgrade is available). Hp Designjet 5500 Ink top HP Customer Care Click here to go online to HP Customer Care.

If the error appears, continue with the remaining steps. Recommended action Remove the media and turn the printer off then on (using the power switch located on the back of the printer). NOTE: Remove and replace any low or empty cartridges. his comment is here XX05 Replace The printhead detects that the cleaner does not match the rest of the ink system already installed.

Click here for information on contacting HP Customer Care. Ensure the language setting is correct and click OK. Select the system software (firmware) according to what operating system is in use. Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on.

Scroll to Test Print and press Enter. top System Error 0B000E (non-continuable) Explanation At power up, the printer thinks it is smaller than 42 inches. NOTE: Proceed with the following steps before pressing ENTER on the keyboard. Hinzufügen Playlists werden geladen...