Home > Hp Designjet > Hp Designjet 5500 Error

Hp Designjet 5500 Error

It always happens during initialisation, while checking the printhead cleaners. If no error appears, print several internal test prints to verify printer functionality. You can change this preference below. When the READY message is displayed on the front-panel, scroll to the Printer Setup Options icon and press the Enter key. Check This Out

If the error continues, call HP for technical support to troubleshoot the problem. The error should disappear; however, if the error does return, turn the printer off and plug the power cord into a different power socket. If no problem is found with cable connections or the problem persists, continue with the remaining steps. Using the Arrow keys, scroll to Utilities and press Enter. website here

Reconfigure the IP address. top System Error ffff ffff 036000bd Explanation The Printhead cleaners are incorrectly inserted or there is a problem in the Service Station. Turn the printer on. At the printer, turn the power to the printer off, using the power switch at the back of the unit.

Anmelden 1 Wird geladen... Turn the printer on. WARNING: To prevent possible injury, always remove the power cable from the back of the printer before connecting/disconnecting any internal printer cables or performing any repairs. Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on.

Turn the printer off, wait 15 seconds and turn the printer on. Click here for information on contacting HP Customer Care. top System Error 040000 01E603D9 Explanation A Parallel Port error has occurred. over here top System Error 0B0003 (non-continuable) Explanation ADCO Internal channels check failure.

The way to get around this if you need the yellow was to take off the tabs which let you insert the light magenta into the yellow channel, taek the chip NOTE: Before troubleshooting System Errors, if possible, repeat the procedure performed when the error was reported. Wird verarbeitet... Ensure the clear plastic tube is connected and not kinked in any way.

Replace any out of warranty or faulty print heads. his explanation This document contains a comprehensive list of various support services available to help solve printer problems. Recommended action Clean all printhead/carriage electrical contacts Change the lens cover Clean the bottom of the line sensor and carriage Clean the slider rods Clean the drive rollers Clean mark encoder Use the information below to determine the cause of the failure and perform the necessary troubleshooting steps to resolve.

Melde dich an, um unangemessene Inhalte zu melden. his comment is here It always happens during initialisation, while checking the Printhead Cleaners. Re-boot the printer and the error code should not appear again 58 Designjet 5000 / 5500 0D0005 03180382 error (Non-Continuable) After cutting the media, the Printer cannot deactivate the cutter 59 Designjet 5000 Return to TWI Documents Library Index Page HP Designjet 5000 and 5500 Series - TWI: System Error 0B0004, 0B0005 In this document: Parts required (part numbers are subject to change) Troubleshooting

Melde dich an, um unangemessene Inhalte zu melden. Hochgeladen am 15.09.2010Within the HP 5000 5500 Designjet printers and other designjets with tube systems, they can get air in the tube system from fault on the ink cartridge or worn Wird verarbeitet... this contact form Highlight and select Upgrade Firmware.

The printer will display the following messages: Lift the Window, Clean Roller Mark, Replace Lens, and Lower the Window, and press ENTER to continue. If the error continues, call HP for technical support to troubleshoot the problem. Press the BACK key again to return to the Service Utilities menu.

Wird geladen...

WiedergabelisteWarteschlangeWiedergabelisteWarteschlange Alle entfernenBeenden Wird geladen... Release the locking tabs on both ends of the memory DIMM(s). Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. Wird verarbeitet...

When the READY message is displayed on the front-panel, scroll to the Printer Setup Options icon and press the Enter key. Depress, and hold down the DOWN ARROW and the TOP keys simultaneously, while turning the power to the printer back on. (Use the power switch at the back of the unit.) Recommended action Turn the printer off (using the power switch at the back of the printer), and check for obstructions in the Carriage path (Scan-axis) and remove if found. http://upintheaether.com/hp-designjet/hp-designjet-5500-error-messages.php Click here for information on contacting HP Customer Care.

Click here for information on contacting HP Customer Care. Click here for information on contacting HP Customer Care. Recommended action Turn the printer off, using the main power switch located on the back of the printer. Nächstes Video HP 5000 5500 Designjet printer keeps asking to replace printhead within a short time. - Dauer: 0:55 Les Sheppard 54.720 Aufrufe 0:55 HP DesignJet 5500 UV Ink Replacement -

Scroll to Test Print and press Enter. Press the Up Arrow key to move the drive roller until the Mark encoder is visible. If any of the printers are out of date, the application will prompt an update. If the error continues, call HP for technical support to troubleshoot the problem.

The User's Guide that came with your HP product. Send the copy command from the PC (press Enter on the keyboard), which will send the firmware upgrade file (typed in during Step 1) to the printer. due to a temporary loss of tension). There is nothing wrong with the printer.

Recommended action Press ENTER on the printer's front panel to continue. Click here for information on contacting HP Customer Care. Was the information on this page helpful? Click here for information on contacting HP Customer Care.

On the printer's front panel, scroll to the Cartridges menu. Upgrade the firmware to the most current version available (instructions below). If the error persists, upgrade the printer firmware (if upgrade is available).