Home > Hp Designjet > Hp Designjet 5500 Error Messages

Hp Designjet 5500 Error Messages

Contents

Even if the error appears again, there is nothing wrong with the Printer. System Error: 0D0000 033f019C Problem Description: No Media Profiles Available. Corrective Action: Try the following: Check that the Paper-Axis Motor cable is NOT broken or damaged. Wähle deine Sprache aus. http://upintheaether.com/hp-designjet/hp-designjet-5500-error.php

System Error: 0B0003 Problem Description: ADC0 Internal channels check Failure. If the tubes system is priming: install setup printhead(s) Ensure that HP No. 81 printheads are installed. System Error: 0C00FF Problem Description: Print Mask could not be generated. The front panel will display the ink level and indicate when the ink supply is low, very low, or empty. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpp03771

Hp Designjet 5500 Service Manual

Plug the power cable back into the printer. Click here for information on contacting HP Customer Care. If the two LED's are ON and the error continues, replace the Main PCA Page 8-79. Corrective Action: Replace the Main PCA Page 8-79.

top System Error 050000 (continuable) Explanation The Lens is having problems reading the Mark Encoder on the Drive roller. Corrective Action: Replace the Main PCA Page 8-79. Corrective Action: Refer to System Error Code ffff ffff 030d0170 or ffff ffff 030d0171. Hp Designjet 1050c Error Codes Replace the Main PCA Page 8-79.

XX03 Replace Printhead smartchip failure. Hp Designjet 5500 Printhead Reseat Error Click here for instructions on how to upgrade the printer's firmware . This document contains a comprehensive list of various support services available to help solve printer problems. Press the UP or DOWN arrow key to select the Printheads icon, and view information on the printheads (see Figure 7).

top System Error ffff ffff 02b301b0 Explanation A firmware error occurred during a Printhead Alignment. Hp Designjet 5500 Manual Pdf Following initialization, verify recognized memory through the front panel (Printer Setup, Utilities, Statistics, RAM present=). Recommended action Remove and re-install the Printhead cleaners. If the error continues, call HP for technical support to troubleshoot the problem.

Hp Designjet 5500 Printhead Reseat Error

If it still fails, report the error to the division.

Recommended action Remove the media and turn the printer off then on (using the power switch located on the back of the printer). Hp Designjet 5500 Service Manual Using this procedure you will be able to determine exactly which component failed. Hp 5500 Printhead Problems Corrective Action: Try the following: Replace the Carriage Assembly Page 8-46 Replace the Trailing Cable Page 8-36.

Click here for information on contacting HP Customer Care. his comment is here Reseat or add memory (if needed). HP Designjet 5500 From the above location, type copy /b DJ5500_Axxxx.FMW LPT1 (the xxxx refers to the most current firmware revision). Your cache administrator is webmaster. Hp Designjet 5000 Service Manual

Click here for information on how to replace the Lens cover . The ink cartridge color on the overlay indicates the ink cartridge color related to each bar. Using this procedure you will be able to determine exactly which component failed. this contact form Power OFF the Printer and allow the Printer to dry for 15 minutes.

Click here for information on contacting HP Customer Care. Hp Designjet 5500 Air In Tubes Wird geladen... Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on.

The printhead must be replaced after the print job.

Continuable and non-continuable error codes Some error codes are continuable, which means that it is possible to press ENTER on the front panel and continue working with the printer. If the error continues, call HP for technical support to troubleshoot the problem. Replace the APS Page 8-65. Hp Designjet 5100 Error Codes NOTE: Proceed with the following steps before pressing ENTER on the keyboard.

Turn the Printer OFF and disconnect the Vacuum Fan from the Main PCA. Click here for information on how to replace the Lens cover . WiedergabelisteWarteschlangeWiedergabelisteWarteschlange Alle entfernenBeenden Wird geladen... navigate here Ensure that all the ink consumables are HP No. 81 XX13 Replace XX14 Replace XX15 Replace Printhead smart chip failure.

Faulty APS. Using this procedure you will be able to determine exactly which component failed. Replace the Trailing Cable Page 8-36. top System Error 040000 01E603D9 Explanation A Parallel Port error has occurred.

The printer cannot be used until the priming process has been completed. If the error continues, call HP for technical support to troubleshoot the problem. Click here for information on contacting HP Customer Care.