Home > Hp Designjet > Hp Designjet 5500 Error Codes

Hp Designjet 5500 Error Codes

Contents

top System Error 0B0006 (non-continuable) Explanation The Trailing cable has been incorrectly connected. CAUTION: When cleaning the Printheads, do not wipe or clean the firing nozzles on the bottom of the Printhead. The current status of the printhead. On a couple of occasions the printer has also displayed 0b000a 030f053b and "Check Cleaner Path." These have appeared only a few times out of the thirty-or-so restarts. Check This Out

Remove the ink cartridge and reinstall. 2. If the error continues, call HP for technical support to troubleshoot the problem. Open the folder when prompted, once the download is complete. Thank you! http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpp03771

Hp Designjet 5500 Service Manual

Also inspect ALL Ink Cartridges for any signs of leaking (the bottom valve of the Ink Cartridge will contain ink). I'd appreciate any help you can offer. The possible causes are fibers or paper in the Drop Detect sensor, or that the Scan-Axis reference is incorrect. To see information on a specific color cartridge, press the ARROW keys until the front panel highlights that color (see Figure 4), and then press the ENTER key.

Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. Ensure that the ink cartridge is the correct color for that slot. Was the information on this page helpful? Hp Designjet 1050c Error Codes XX02 Reseat There is a problem with continuity problem between the ink cartridge and ink supply station. 1.

If error appears again, Call HP Support top System Error 0D0005 03180382 (non-continuable) Explanation The printer cannot deactivate the Cutter after cutting the media. Hp Designjet 5500 Printhead Reseat Error Faulty APS. Use at your own risk. see this here Connect a New Aerosol Fan (comes with the new Right Cover) to the Main PCA and power ON the Printer.

Click here for information on contacting HP Customer Care. Hp Designjet 5500 Manual Pdf Attempt to print. However, sometimes the same system error appears quite often or it is permanent. Recommended action Press ENTER on the printer's front panel to continue.

Hp Designjet 5500 Printhead Reseat Error

Remove the setup printheads and replace them with printing printheads.

Anmelden Transkript Statistik 24.362 Aufrufe 14 Dieses Video gefällt dir? Hp Designjet 5500 Service Manual Click here for information on contacting HP Customer Care. Hp Designjet 5500 Printhead Error Codes This error code appears when the printer detects that the same areas of nozzles do not work in different printheads.

If the error persists, upgrade the printer firmware (if upgrade is available). http://upintheaether.com/hp-designjet/hp-designjet-5500-error-messages.php Proceed to section titled “Upgrade process”. Corrective Action: Try the following: Check that the Paper-Axis Motor cable is NOT broken or damaged. Replace the Main PCA Page 8-79. Hp 5500 Printhead Problems

Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. Corrective Action: Try the following: Check that the Service Station Cable (the grey flat cable with the grey connector) is plugged into the Main PCA, and that the clips of the Replace the Carriage Assembly Page 8-46. this contact form Click here for information on contacting HP Customer Care.

If the error re-appears, call HP for technical support to troubleshoot the problem. Hp Designjet 5500 Air In Tubes Schließen Ja, ich möchte sie behalten Rückgängig machen Schließen Dieses Video ist nicht verfügbar. The service station motor may be dying or the voltage to the motor may be low.  I would wait to see if the PS solves the other problem first.  It may

Corrective Action: Re-boot the Printer and make sure that the Window is never opened during the cutting operation.

Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. There is nothing wrong with the printer. top System Error 0F0200 00b007E5 (non-continuable) Explanation Internal crash error involving media profiles and memory. Hp Designjet 5000 Service Manual Possible causes are memory corruption, print mode definition incompatible with mask restrictions (if using an external RIP).

System Error: ffff ffff 036e0136 Problem Description: This is an internal general error code which can appear during the Printhead Alignment process. Click here for information on contacting HP Customer Care. If the error code continues, replace the Main PCA Page 8-79. http://upintheaether.com/hp-designjet/hp-designjet-5500-error.php NOTE Even though the customer can continue working with a Continuable Error Code, an on-site visit should still be planned to troubleshoot the problem.

System Error: ffff ffff 01dcxxxx Problem Description: There is a problem with the I/O Card (happens during power-up). Transkript Das interaktive Transkript konnte nicht geladen werden. Check that the Carriage moves freely from side to side. Install normal printheads.

If there is ink leakage, replace ALL Ink Cartridges, the APS ( Page 8-65) and the Tubes System ( Page 8-25). Status Numbers Printhead Cleaner Error Description Procedure *X03 Replace There is a printhead cleaner detection failure (you may continue to use the printhead cleaner) Try the following: 1. If the error continues, call HP for technical support to troubleshoot the problem. Click here for instructions on how to upgrade the printer's firmware .

Recommended action Press ENTER on the printer's front panel to continue (the printer will still function, although the heater will be disabled). Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. WARNING Only replace one component at a time and check if the error has gone before replacing another component.