Home > Hp Designjet > Hp Designjet 500ps Error Messages

Hp Designjet 500ps Error Messages

Contents

Turn on the printer, following initialization re-send the file that generated the error. Once the update is complete, the front panel will indicate that the printer must be disconnected. If the Troubleshooting Test Print is successful, go to troubleshooting connection . f. Check This Out

Following a successful troubleshooting plot, internal printer functionality has been verified. HP Designjet Customer Care cannot do this. Disconnect the power cord. 2. From the front panel message of Ready, highlight the printer icon, and press ENTER. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c00993566

Hp Designjet 500 Error Code 21 10

Turn the printer on and attempt to verify functionality. Follow the instructions to perform the update. Recommended action NOTE: Before continuing, verify that the parallel cable being used is an IEEE 1284 compliant cable no longer than 10 feet in length. Click here to download HP drivers and/or software .

Wiedergabeliste Warteschlange __count__/__total__ Designjet 500 21:10 service error FixYourDesignJet AbonnierenAbonniertAbo beenden468468 Wird geladen... If the problem persists, click on Support at the top of the page for additional HP support and contact options. Reconnect the power cord. 7. Hp Designjet 800 Formatter Card Turn off the HP Designjet 500, 510, or 800 series printer and disconnect the parallel cable and any network cables, leaving only the power cable connected.

If even after this, the carriage is STILL NOT able to come out, contact technical support for specific instructions about unlocking the carriage. 4. Uninstall and reinstall the printer driver (install the most current version available). Click here for detailed instructions on network card removal . http://h20564.www2.hp.com/hpsc/doc/public/display?docId=mmr_kc-0102406 Upgrading printer firmware top Follow these steps to check for the latest firmware updates for your printer using the HP website.

Non-continuable error codes do not allow work with the printer to continue. Warning 61 05 Hp Designjet 500 Ensure the parallel cable is properly connected to the PC and printer. Reinstall the accessory card cover. Recommended action Follow the instructions below to help solve the issue: Turn the printer off and allow a few minutes for printer to cool.

Hp Designjet 500 Error Codes

If the error message persistss, check for a new release of the driver and/or upgrade the printer's firmware. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-c03146392 Wird geladen... Hp Designjet 500 Error Code 21 10 Wird geladen... Hp Designjet 500 System Error 21 10 Turn the printer off.

If the error occurred while trying to access the IO Menu, then there is a solution : just upgrade to firmware A.02.08 , which in fact solves this problem. his comment is here Verify that the correct printer driver is being used. If the error persists, try replacing the black printhead first (most common cause), or replace any other printhead displaying error messages. Recommended action Turn the printer off. Hp Designjet 500 Error 79 04

Check for a new release of the firmware and upgrade to the latest version if needed. In the Firmware section, click Download. One of the out-of-ink sensors (located in the Ink Supply Station) is not reporting what it should during the initializing process while depressurizing. http://upintheaether.com/hp-designjet/hp-designjet-500ps-system-error.php If the error message persistss, check for a new release of the driver.

Try a different parallel port mode on the computer. Hp Designjet 800 System Error 05 10 If AppleTalk is not being used to send the binary file to the printer, change the printer's internal PostScript settings to Binary (Set-up menu, PS settings, Encoding, Binary). Very helpful Somewhat helpful Not helpful End of contentUnited StatesHP WorldwideStart of Country / Region Selector contentSelect Your Country/Region and LanguageClick or use the tab key to select your countryArgentinaAustraliaBelgiqueBoliviaBrasilCanadaCanada-françaisČeská republikaChileColombiaDeutschlandEcuadorEspañaFranceIndiaIrelandItaliaMagyarországMéxicoNew

Your cache administrator is webmaster.

Anmelden Teilen Mehr Melden Möchtest du dieses Video melden? Thank you! This will improve the general functionality of the device. Hp Designjet 500 Firmware Update Download If the problem persists, click on Support at the top of the page for additional HP support and contact options.

If the Troubleshooting test print is successful, go to troubleshooting the connection section. top Removing/Installing (formatter card, HP-GL/2 card, Jetdirect print server) Turn the printer off and unplug the power cord. Change the rotate setting in the Page Format menu of the printer to zero (0) by following these steps: Delete any print jobs from the Macintosh Print monitor or Desktop Print http://upintheaether.com/hp-designjet/hp-designjet-500ps-error-codes.php When the contacts are dry, reinstall the printheads and close the carriage cover.

Recommended action Turn the printer off and allow a few minutes for printer to cool. Turn the printer on and attempt to verify functionality. Try sending a different file. Recommended action Follow the instructions below to help solve the issue: Turn the printer off and allow a few minutes for printer to cool.

Du kannst diese Einstellung unten ändern. If the problem persists, click on Support at the top of the page for additional HP support and contact options. IMPORTANT: For the DJ 500, it is recommended to remove the HPGL2 card (if installed) before updating the FW. top top 79:04 errors when using version A.02.02 firmware or newer 79:04 error means "unexpected," "unknown," or "not assigned." Some of these errors are now better understood and have been remapped

Press the ARROW buttons to select Graphics Language, and press ENTER. IMPORTANT: Every PH has its own expiration date stamped on it. top System error 05:10 (only applicable for Designjet 500 series) Explanation HP-GL/2 accessory card failure. Turn the printer on and attempt to verify functionality.

Recommended action Follow the instructions below to help solve the issue: Turn the printer off and allow a few minutes for printer to cool. Clean the electrical contacts on the carriage and the printheads using a lint-free cloth (i.e. top System error 93:10 Explanation Ink System startup failed.