Home > Hp Designjet > Hp Designjet 5000 System Error

Hp Designjet 5000 System Error

Contents

Was the information on this page helpful? This error code appears when the printer detects that the same areas of nozzles do not work in different printheads. Check that the Air Tube from the APS is correctly connected to the Tubes System. Recommended action Press ENTER on the printer's front panel to continue. Check This Out

All necessary files will be installed. After 10-15 seconds, turn the main power switch on. System Error: 0F0200 01E603d2 Problem Description: This is an error that is related to the Parallel Port. top System Error 0B0005 (non-continuable) Explanation Air Pressurization System (APS) failure.

Hp Designjet 5500 Error Codes

Corrective Action: Try the following: Replace the Carriage Assembly Page 8-46 Replace the Trailing Cable Page 8-36. Replace the ISS PCA Page 8-86. If the error persists, upgrade the printer firmware (if upgrade is available).

Click here for information on contacting HP Customer Care. Its root cause (as explained above) may not necessarily be a firmware problem; it could also be related to the Ink Supplies, Electronics Module, etc. Click here for information on contacting HP Customer Care. Hp Designjet 5500 Printhead Error Codes If the error continues, call HP for technical support to troubleshoot the problem.

The error code should not appear again. Hp Designjet 5500 Printhead Reseat Error If the error continues, call HP for technical support to troubleshoot the problem. WARNING Only replace one component at a time and check if the error has gone before replacing another component. Recommended action Remove and re-install the Printhead cleaners.

Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. Hp 5500 Printhead Problems Click here for information on contacting HP Customer Care. Check that the IDS Crane is installed correctly on top of the Carriage and that the Carriage Cover is clipped on correctly. If the error code continues, replace the PCA Page 8-79.

Hp Designjet 5500 Printhead Reseat Error

If there are third-party software drivers and RIPs installed, refer to their user documentation. original site The printhead must be replaced after the print job. Hp Designjet 5500 Error Codes If error appears frequently upgrade to firmware release A.02.xx 57 Designjet 5000 / 5500 0D0004 xxxxxxxx error (Non-Continuable) This is an internal general error code which can appear during the Printhead Hp Designjet 5500 Service Manual Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on.

If the Error Code continues, replace the Main PCA Page 8-79 taking care when connecting the Trailing Cable. his comment is here If the error continues or persists, replace the Lens cover. Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. Perform the Recovery procedure. Hp Designjet 1050c Error Codes

Turn the printer on. top Printhead cleaner errors (first digit = A or *) When replacing printhead cleaners, perform the following tasks: Ensure that the printhead cleaner is the correct type. Scroll to Replace ink cartridges and press ENTER. this contact form The Service Configuration Print if possible Page 1-37.

Click here for information on contacting HP Customer Care. Hp Designjet 5000 Service Manual DesignJet Plotter RepairRepair Tips for DesignJet Plotters Tech TipsPlotter FixLJ RepairTech Links HomeLog in Find admin04/11/06 DesignJet 5000 Series Error Codes Link: http://www.computercare.cc/osc/catalog/index.php?cPath=67TweetDesignJet 5000 Series Plotter System Error Codes Introduction Loosen the two thumbscrews that attach the HP Jetdirect EIO card.

System Error: 0B000C Problem Description: Serial Device ADC test failure.

Recommended action Download a media profile for the ink type being used (if available). Clean the Mark encoder (small slotted white plastic insert on the left end of the roller) using a lint free cloth lightly dampened with water. If the problem persists following the upgrade, replace the lens cover: Scroll to the Printer Setup Options icon and press the Enter key. Hp Designjet 5500 Manual Pdf The Parallel Port setting in the PC BIOS should be in the ECP mode.

Recommended action Turn the printer off (using the main power switch on the back of the printer) and remove the network cable from the printer's network card. Replace the Trailing Cable Page 8-36. This configuration should eliminate or decrease the frequency of this error. navigate here If the problem continues to appear and the customer is using an external RIP, ask them to try one of the internal print modes by printing from the HP Driver.

Reseat the printhead cleaner Check that the lens is clean and perform lens maintenance if required. Open the cover on the back of the printer to access the ink cartridge assembly (right side of the printer, looking from the back).