Home > Hp Designjet > Hp Designjet 5000 Error Messages

Hp Designjet 5000 Error Messages

Contents

Select YES to replace printheads or select NO to finish print job without the failed printhead (print quality is affected). NOTE: Proceed with the following steps before pressing ENTER on the keyboard. If the error immediately re-appears call HP for technical support. Depending on the print mode being used (Max. Check This Out

Check all the tubes of the APS and Tubes System and make sure they are correctly connected and are NOT pinched or damaged. Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. Wird verarbeitet... XX05 Replace Used setup printheads installed.

Hp Designjet 5500 Printhead Reseat Error

top System Error ffff ffff 030d0170 Explanation At power up, the printer thinks it is smaller than 42 inches. Ensure the clear plastic tube is connected and not kinked in any way. Explanation Internal crash error involving media profiles and memory.

If the error continues or persists, replace the Lens cover. The following table describes the messages and status codes for HP ink supplies, and the recommended actions. If the error persists, please call HP for technical support to troubleshoot the problem. Hp Designjet 5000 Service Manual top System Error 0A0030 (non-continuable) Explanation A problem in the Depressurizing Air system has occurred.

Click here for information on contacting HP Customer Care. Hp Designjet 5500 Service Manual WARNING Only replace one component at a time and check if the error has gone before replacing another component. System Error: 0C1001 Problem Description: Primer Shutdown Error. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpp02990 XX20 Recover The printhead has detected nozzle failure. 1.

The first digit of the HP ID code, as shown in Table 2a, identifies the part and provides specific information. Hp Designjet 5500 Air In Tubes Corrective Action: Download a media profile for the ink type being used. Check that the Air Pressurization System Sensor Cable is correctly connected and is NOT damaged. System Error: ffff ffff 03450097 Problem Description: If the Window is opened during the cutting operation, the Printer hangs and the Carriage suddenly stops.

Hp Designjet 5500 Service Manual

Figure 3: Location of DIMM(s) NOTE: J6 - Boot ROM is internal printer firmware. If the error re-appears or problems persist, contact HP support. Hp Designjet 5500 Printhead Reseat Error Click here for information on how to download media profiles . Hp 5500 Printhead Problems Plug the power cable back into the printer.

top Why does the printer require priming? his comment is here If the error continues, call HP for technical support to troubleshoot the problem. Since the information cannot be found, this error code is displayed. Depress, and hold the DOWN ARROW and the TOP key simultaneously, while turning the printer on using the main power switch (may require two people). Hp Designjet 1050c Error Codes

Replace the printhead cleaner. top Printhead cleaner errors (first digit = A or *) When replacing printhead cleaners do the following: Ensure that you have the correct printhead cleaner. System Error: ffff ffff 036e0136 Problem Description: This is an internal general error code which can appear during the Printhead Alignment process. this contact form Ensure the clear plastic tube is connected and not kinked in any way.

If the error re-appears, call HP for technical support to troubleshoot the problem. Hp Designjet 5100 Error Codes If the error re-appears, continue with the remaining steps. Corrective Action: Try the following: Replace the Lens Cover Page 9-5.

Click here for information on contacting HP Customer Care.

If the error continues, call HP for technical support to troubleshoot the problem. The system returned: (22) Invalid argument The remote host or network may be down. Three sources of information are readily available to help you find an HP Support Services phone number: The Web: Click here to go to HP Customer Care online Support Guide. Hp Laserjet 5500 Error Codes If no error appears, try to print a file (problem is resolved if printer prints the file with no error).

System Error Codes consist of two groups of alphanumerics: [XXXXXX]-[YYYYZZZZ] The first set of 6 alphanumeric characters consists of the System Error and the second set of 8 digits, when present, If the tubes system is priming: install setup printhead(s) Ensure that HP No. 81 printheads are installed. Using this procedure you will be able to determine exactly which component failed. navigate here XX06 Replace The printer detects an incorrect printhead cleaner.

Status Code First Digit Part/Information 0 HP No.81 Printhead in warranty 1 HP No.81 Printhead out of warranty 4 Setup printhead 5 Printhead smart chip error A HP No.81 Printhead cleaner Using this procedure you will be able to determine exactly which component failed. Using this procedure you will be able to determine exactly which component failed. Status Numbers Error Description Procedure XX03 Replace The ink cartridge has a leak, which prevents the ink pumping to the printer.

Allow printer to complete initialization. The printer will not setup correctly without them installed. Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. Recommended action Press ENTER on the printer's front panel to continue.

System Error: 0B0002 Problem Description: Bad IDS pressure read.