Home > Hp Designjet > Hp Designjet 5000 Calibration Error

Hp Designjet 5000 Calibration Error

Contents

Recommended action Press ENTER on the printer's front panel to continue. Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. Home Forum New Posts FAQ Calendar Community Groups Albums Member List Thanks / Like Statistics Hottest Threads / Posts Forum Actions Mark Forums Read Quick Links Today's Posts View Site Leaders http://upintheaether.com/hp-designjet/hp-designjet-5000-calibration-error-1040.php

When the READY message is displayed on the front-panel, scroll to the Printer Setup Options icon and press the Enter key. Powered by vBulletin Version 4.2.2 Copyright © 2016 vBulletin Solutions, Inc. Click here for information on contacting HP Customer Care. If printer initialization completes (printer goes to a Ready state), continue with Step 6.

Hp Designjet 5500 Error Codes

Replace the Lens Cover Assembly Ÿ Page 9-5. Die Bewertungsfunktion ist nach Ausleihen des Videos verfügbar. Click here for information on contacting HP Customer Care. if no success then i'd go for the replacing of the trailing cable...

Click here for information on contacting HP Customer Care. If the error continues, call HP for technical support to troubleshoot the problem. Now it's "0406 reset" for the pink printhead. The cable being used (by part number) and where it was purchased.

Highlight and select Upgrade Firmware. Home Forum New Posts FAQ Calendar Community Groups Albums Member List Thanks / Like Statistics Hottest Threads / Posts Forum Actions Mark Forums Read Quick Links Today's Posts View Site Leaders Clean the Mark encoder.

If the error code reappears, the printer may require an on-site visit to resolve the problem.

Turn the printer off (using the power switch at the back of the printer), and allow the printer to cool for 15 minutes. top System Error 010091 (continuable) Explanation An error has occurred in the Paper-axis Motor Encoder. Click here for information on contacting HP Customer Care. Turn the printer off, wait 15 seconds and turn the printer on.

Hp Designjet 5500 Printhead Reseat Error

If the tube is not connected (blue end only), re-connect as needed; also eliminate all kinks noticed in the tube. http://www.copytechnet.com/forums/hp/49105-hp-designjet-5000-error.html Re-cover the offending printhead(s). Hp Designjet 5500 Error Codes The program will proceed to upgrade the firmware. Hp Designjet 5500 Printhead Error Codes Turn the printer on.

If the error continues, call HP for technical support to troubleshoot the problem. http://upintheaether.com/hp-designjet/hp-designjet-5000-calibration-error-0021.php Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. Du kannst diese Einstellung unten ändern. top System Error 0A0040 (non-continuable) Explanation Air Pressurization System (APS) failure. Hp Designjet 5500 Printhead Cleaning

Out of the blue just failed. The front panel will display Firmware Upgrade. I put in the new print head and it calibrated fine and shows all print heads OK. this contact form If the error continues, call HP for technical support to troubleshoot the problem.

Corrective Action: „ 0021 Calibration Error: Line Sensor error. If the error immediately re-appears call HP for technical support. top System Error 0B000B (non-continuable) Explanation Air Pressurization System failure.

Recommended action HP recommends printing via the network card because the transmission time via the parallel port is very slow, which may be causing the error.

Ensure the clear plastic tube is connected and not kinked in any way. Three new printheads can't all be bad. NOTE: Proceed with the following steps before pressing ENTER. Reply With Quote 03-15-2011 #4 JustManuals View Profile View Forum Posts Field Supervisor 10,000+ Posts Join Date Jan 2006 Location Las Vegas, NV Posts 10,067 Post Thanks / Like Thanks (Given)

The printer will display the following messages: Lift the Window, Clean Roller Mark, Replace Lens, and Lower the Window, and press ENTER to continue. Click here for information on how to replace the Lens cover . If the error persists, call HP for technical support to troubleshoot the problem. navigate here top System Error 0B0005 (non-continuable) Explanation Air Pressurization System (APS) failure.

If the error continues after replacing the lens cover, call HP for technical support to troubleshoot the problem. If the error persists for that color, replace the Printhead. Don't show me this message again. Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on.

Place the lens back into the printer’s top cover for use at a later time. Recommended action Turn the printer off (using the power switch at the back of the printer). NOTE: Before troubleshooting System Errors, if possible, repeat the procedure performed when the error was reported.