Home > Hp Designjet > Hp Designjet 500 System Error 86

Hp Designjet 500 System Error 86

Contents

If problems persists, continue with the remaining steps. top System error 79:04 Explanation Miscellaneous firmware error. If the problem persists, click on Support at the top of the page for additional HP support and contact options. Wenn du bei YouTube angemeldet bist, kannst du dieses Video zu einer Playlist hinzufügen. Check This Out

If the carriage is stuck at the right hand side of the Printer and cannot be moved out to the center of the Print Platen, likely it is because the Service clear paper path4. top System error 61:04 Explanation Firmware error. Recommended action Turn the printer off and allow five minutes for printer to cool. http://h30434.www3.hp.com/t5/DesignJet-Large-Format-Printers-and-Digital-Press/Solved-HP-DesignJet-500-Error-86-01-when-trying-to-trim/td-p/5054713

Hp Designjet 500 Error 86:01

If the percentage is close to 100%, then lubricate the Slider Rod (there is probably too much friction in the Slider Rod). From the main front-panel menu, select the Ink menu and press Enter. it was really bumpy and stiff. Turn on the printer, following initialization re-send the file that generated the error.

If AppleTalk is not being used to send the binary file to the printer, change the printer's internal PostScript settings to Binary (Set-up menu, PS settings, Encoding, Binary). Clean and lubricate the carriage rail. top System error 64:03 Explanation USB port communication problem. Hp Designjet 500 Severe Error 0x8010003 Firmware must be upgraded to A.02.04 or higher.

Recommended action Click here to view more detailed troubleshooting information . Turn the printer on and attempt to verify functionality. One of the out-of-ink sensors (located in the Ink Supply Station) is not reporting what it should during the initializing process while depressurizing. https://h20565.www2.hp.com/hpsc/doc/public/display?sp4ts.oid=3558640&docId=emr_na-c04581797&docLocale=en_US The cutter can also be installed incorrectly causing the error.  The tires on the cutter need to straddle the guild rail it sits on.  If you pull the cutter out to

Turn on the printer, following initialization re-send the file that generated the error. Hp Designjet 500 Error Codes If the problem persists, continue with the remaining steps. top System error 01:11 Explanation The electronics module has detected a connection problem with the cooling fan. Respond to this 0 I found this guide on HP's website that may be useful to you.The 86.01 is a carriage movement failure.

Hp Designjet 500 System Error 81:01

If the problem persists, click on Support at the top of the page for additional HP support and contact options. If the problem persists, click on Support at the top of the page for additional HP support and contact options. Hp Designjet 500 Error 86:01 Click here for instructions on upgrading the printer's firmware . Hp Designjet 500 Paper Jam Error Click here to download HP drivers and/or software .

Showing results for  Search instead for  Do you mean  or Post new question Question Reply Topic Options Subscribe Mark Topic as New Mark Topic as Read Float this Topic to the http://upintheaether.com/hp-designjet/hp-designjet-111-printer-system-error-2.php Figure 2: Screws securing Formatter card, HP-GL/2 card, or Jetdirect print server NOTE: The 500 and 800 series printers have different cards (Formatter, HP-GL/2 accessory, or Jetdirect print server) that may The preferred slot for the Formatter card and the HP-GL/2 accessory card first slot in the printer (outside slot). In any case, one who renders repairs to HP Designjet printers (self-help) is strongly recommended to refer to the applicable HP Service Manual, updates and service notes. 86.01 Possible Paper Jam

I also upgraded the firmware to version A.04.02 and still get the error.I have searched on this subject and so far nothing I see seems to be like this problem. top System Error 17:11 (only applicable for Designjet 500 series) Explanation A problem has been detected while initializing. Any suggestions by unknown on Nov 16, 2012 at 2:52pm Add comment Please sign in to comment 0 error 86:01possibly paper jam1. this contact form Close the top cover and turn the printer on.

Remove the formatter card and re-install the formatter card. Hp Designjet 510 Error Codes The carriage then returns to service bay and error code appears. Remove and re-seat the network card.

Recommended action If error 65:03 occurs when trying to access the printers front panel IO menu, upgrade the firmware to v.

Recommended action If the problem persists, click on Support at the top of the page for additional HP support and contact options. Superimposed is a lot of ink splatter. If the problem persists, click on Support at the top of the page for additional HP support and contact options. Hp Designjet 500 Error 79:04 Click here for instructions on upgrading the printer's firmware .

Delete the Jetdirect port and recreate the port using Microsoft Standard TCP/IP port. Using a lint free cloth dampened with water, clean the trailing cable and the underside of the printer frame that holds the ink-tube system. Lift the blue lever and insert the folder into the paper path to remove jammed paper. navigate here Following replacement, turn the printer on and attempt to verify functionality.

Remove the right cover and check the cable connection between the Interconnect PCA and the Service Station motor.