Home > Hp Designjet > Hp Designjet 500 System Error 2110

Hp Designjet 500 System Error 2110

Contents

Follow the steps directly below to unlock the Carriage from the Service Station: Highlight the Set-Up menu and press the ENTER button. On the other hand, feel free to update the FW if the printer is able to get to ready at any point. Move it all the way to the left & have a good look where it normaly sits (on the right) thats where i found a tiny bit of paper. 1 Kudo For doing this, remove the Card Cover from the back of the Left Hand Cover. Check This Out

Move it all the way to the left& have a good look where it normaly sits (on the right) thats where i found a tiny bit of paper. 0 Kudos ACADuser Okay, I found another error, I'll go look that up, too... f. The new Service Station does not have an Aerosol fan and older firmware will check for the Aerosol fan, thus causing another system error. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=mmr_kc-0102406

Hp Designjet 500 Service Station

To fix this problem you need to follow the steps here: Click Here --------------------------------------------------------------------------------------------------------------------- Ask Your Own Printers Question Customer: replied6 years ago. Privacy Policy Terms of Use Create Account Sign In Help CommunityCategoryBoardArticlesUsers turn on suggestions Auto-suggest helps you quickly narrow down your search I had gone ahead and given that a try last week (the gunk *was* pretty nasty, but, didn't actually seem to have been the source of the error, even after unplugging/clearing, The Carriage assembly should now be free from the Service station.Figure 1: Service Station Gear If an obstruction is found and removed, plug the power cord in, turn the printer On

c. Learn more You're viewing YouTube in Russian. Respond to this 0 Did you just by chance replace the belt and now you get the error or has it worked just fine and the error just came up. Hp Designjet 500 System Error 22 10 b.

Remove all PRINTHEADS (PHs) from the carriage. Back to TWI Documents Library Index Page Web computercare.cc Save Big on OEM New, Remanufactured and Close the Window. 6.

reading System Error 21:10.

Causes of this error can include the Service Station or Carriage. Hp Designjet 500 Error Codes By using Dailymotion, you are giving your consent to our cookies. Thanks, Melanie Perry ***not all who wander are lost*** http://augi.com/autocad http://mistressofthedorkness.blogspot.com 0 Kudos *Wanderer

Post 2 of 12 Share Report Re: HP DesignJet 800ps - Error 21:10 Options Mark as open your front wondow& see if you can slide the carrage up& down.

Hp Designjet 800 Error Code 21 10

d. http://www.computercarefiles.com/TWI_Docs/bpp90134/ The flag should stay at about a 45-degree angle. Hp Designjet 500 Service Station If the first you probably pinched the big grey ribbon cable when you put the service station bracket back on. Hp Designjet 800 Service Station On 2/25/2010 10:56 AM, chris.kershaw wrote: > Ive just had this on my DJ800 all it was is a bit of paper stuck under the carrage with the printheads on.

Simply disassemble and clean with lukewarm water in a sink to clean out the ink residue. Категория Хобби и стиль Лицензия Стандартная лицензия YouTube Ещё Свернуть Загрузка... Автовоспроизведение Если функция включена, his comment is here Ensure that the printer is SPECIAL X MODE (this is needed as the printer is not able to get to ready): • Disconnect the power cord. • Press the CANCEL button. If any rejection of PHs appears while replacing them or if the printer is unable to finish the PH alignment, then the expired PHs need to be replaced with new ones If the latter you probably need to replace the service station. Hp Designjet 500 Severe Error 0x3010002

A Bonus and Positive Feed Back are appreciated Ask Your Own Printers Question Customer: replied6 years ago. the pictures do help as well. :-) The other link you posted was very good, too... Customer: replied6 years ago. this contact form by dmzcompute on Aug 1, 2011 at 4:05pm Add comment Please sign in to comment 0 yeah I've pinched that cable before and the carriage sled over and scratched all the

Manually move the carriage to the left (out from the Service Station). Designjet 500 Service Station Cleaning Put the PHs back in when asked to do so. Additional info: System error: 0x3010002task: tMechfile: sequence.cline: 758any thoughts?

What do I do?

Melanie Perry ***not all who wander are lost*** http://augi.com/autocad http://mistressofthedorkness.blogspot.com On 3/2/2010 12:54 PM, ACADuser wrote: > Wanderer, > > Found this, has some decent pics as well. > > http://www.computercarefiles.com/TWI_Docs/bpp90134/default.html Once they have been inserted, make sure to properly close the carriage cover (no need to move the carriage) and window. replied6 years ago. Severe Error: 0x3010002 Task: Tmech File: Sequence.c Line: 758 The service station in this video is typical of used ones.

There is also an update in the firmware to try and help with the issue. How do I get it back 10/17/2016 10/17/2016 Viet - Printer Tech The magenta color is choppy. If so, unplug the power cord immediately. navigate here so, I'm replacing the part right now.