Home > Hp Designjet > Hp Designjet 500 Printheads Error

Hp Designjet 500 Printheads Error

Contents

Does the carriage move at all? Figure 1: An ink cartridge Figure 2: A printhead The printheads, as shown in Figure 1.2, are the components that place minute droplets of ink onto the paper. This can interfere with the operation of the printer. Remove the setup heads and place the normal printheads in the carriage. Check This Out

Try a different parallel port mode on the computer. Troubleshooting HP Designjet 500, 510, or 800 series printer functionality Turn off and turn on the HP Designjet 500, 510, or 800 series printer. Select the specific INDIVIDUAL PRINTHEAD and press enter to examine the status of an individual printhead. Melde dich bei YouTube an, damit dein Feedback gezählt wird. http://h20566.www2.hp.com/hpsc/doc/public/display?sp4ts.oid=377954&docId=emr_na-bpp03052&docLocale=en_US

Hp Designjet 500 Printhead Cleaning

No idea what you mean by changed the truck. Two separate prints are made. Not all paper types are supported for alignment; the printer will tell you if you load the wrong type. The message is still asking for the setup heads and it looks like you have them inserted and that they have already primmed the ink system.

With the power off move the carriage by hand to see if there are any obstructions or movement issues. Keep in mind turning off with the power button in front is like turning off a tv set. Second on the service station when looking from the side is a grey plastic piece which should be at an angle with the top towards the front of the printer. Hp Designjet 500 Not Recognising Ink Cartridges The only problem one might have is if you have a low ink cart it will not perform the procedure.

If a Macintosh is printing to the printer via TCP/IP, you must specify a queue name of BINPS. Hp 11 Printhead Wenn du bei YouTube angemeldet bist, kannst du dieses Video zu einer Playlist hinzufügen. Did the carriage move by itself before you installed the new tube assembly since there may have been another issue with the plotter not known before the tube replacement. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpp03062 When the message in Figure 3 appears, the Printer has determined that one of the Printheads has worn out and should be replaced.

Uninstall and reinstall the printer driver (install the most current version available). Designjet 500 Cartridges Später erinnern Jetzt lesen Datenschutzhinweis für YouTube, ein Google-Unternehmen Navigation überspringen DEHochladenAnmeldenSuchen Wird geladen... Leaving the queue name blank could cause the printer to mishandle binary postscript information. I got into the service menu while turning the printer on at the wall and reset the EEROM again, but it still prompts for the priming procedure.

Hp 11 Printhead

Refer to pages 8-5, 8-6, 8-24, 8-25, and 8-26 of the HP Designjet 500/800 Series Service Manual for instructions.Following replacement, turn the printer on.Allow the printer to complete initialization and verify

Wird geladen... Hp Designjet 500 Printhead Cleaning Melde dich an, um unangemessene Inhalte zu melden. Hp Designjet 500 Printhead Set Figure 8: Opening the window Release the latch on the carriage printhead cover, as shown in Figure 3.4.

They are located under the main window at the top of the printer, as shown in Figure 1.3. his comment is here Figure 6: Replacing the ink cartridge When all cartridges have been successfully installed, the printer's icons will stop flashing. Printhead status To determine the status of the printheads, do the following: From the main front-panel menu, select ink system and press enter. However it is still asking for the starter print heads to complete the priming procedure. Hp Designjet 500 Printhead Alignment Error

by unknown on May 8, 2008 at 2:15pm Add comment Please sign in to comment put a piece of tape on the electrical contacts of the active printheadshello - Anonymous 0 Check for a new release of the firmware and upgrade to the latest version if needed. To replace printheads, follow these steps: From the main front-panel menu, select INK SYSTEM and press enter. this contact form Anmelden Transkript Statistik 117.207 Aufrufe 43 Dieses Video gefällt dir?

I started the priming process by mistake also. - Anonymous 0 Did you try removing the power plug from the plotter and then letting it sit for about 1 minute. Hp Designjet 800 Printhead Part Number Turn the HP Designjet 500, 510, or 800 series printer on and send the Troubleshooting Print from the Ink System menu of the front panel. Can you help me?

Figure 9: Lifting up the printhead cover To remove a printhead, lift up the blue handle, as shown in Figure 3.6.

by dmzcompute on Feb 19, 2009 at 6:20pm Add comment Please sign in to comment 0 am looking for a pdf of the service manual by mvrtech on Aug 31, 2009 Wird verarbeitet... Close cover.Good reception. Hp Designjet 500 Printhead Cover Error by dmzcompute on Sep 13, 2013 at 4:51am Add comment Please sign in to comment 0 I bought the entire tract in INCOREWEB, if I tried everything you said but the

There can be NO contact between the back side of the printhead and the contacts on the carriage assembly. If this is the case, please refer to the documentation or technical support services provided with the other printer. Anmelden 44 6 Dieses Video gefällt dir nicht? http://upintheaether.com/hp-designjet/hpo-designjet-500-error.php If the error reappears, try generating the file again and try to print.

The printer will print and use a small calibration pattern to ensure an optimal match between the paper and the ink. The only way to get into the service menu etc was to turn the printer off at the wall then back on. Does that happen. Melde dich an, um dieses Video zur Playlist "Später ansehen" hinzuzufügen.

by dmzcompute on Sep 18, 2013 at 4:33pm Add comment Please sign in to comment 0 Did you solve your problem different_nick. Send a test print from the printer driver. top Printhead replacement In a normal situation, the Printhead should only be replaced when advised by the Printer. Anmelden 7 Wird geladen...

Troubleshootingpage 12................................................................................................................................................................ Hochgeladen am 26.02.2011How to replace a print head on a DesignJet 500 - covering Designjet model numbers: C7768B C7770B C7769F C7770F C7769C C7770C C7769G C7770GPrintheads: No 11 Black C4810ACyan C4811AMagenta C4812AYellow Schließen Ja, ich möchte sie behalten Rückgängig machen Schließen Dieses Video ist nicht verfügbar. Wird verarbeitet...

Anzeige Autoplay Wenn Autoplay aktiviert ist, wird die Wiedergabe automatisch mit einem der aktuellen Videovorschläge fortgesetzt. Leave the cover open and then turn on the plotter. Diese Funktion ist zurzeit nicht verfügbar. Remove the HP-GL/2 Accessory card if installed.