Home > Hp Designjet > Hp Designjet 450c Error

Hp Designjet 450c Error

Contents

Do them one at a time to identify which cartridge is faulty.Walter by walter9999 on Apr 25, 2006 at 2:13pm Add comment Please sign in to comment Thank you, Walter. Can be a number of items. Anmelden Teilen Mehr Melden Möchtest du dieses Video melden? Driver was downloaded using serial # so there should be no issue there. http://upintheaether.com/hp-designjet/hp-designjet-450c-error-lights.php

So the cartridges dry out.....I soak the heads.....but found another way, which might be useful for others too...never heard of it:!! To do this remove the top cover by releasubg the link on the right side and sliding the cover to the left and off. What do you mean? Check the encoder strip, etc.

Designjet 450c Cartridge Light Flashing

by unknown on Aug 28, 2006 at 6:09am Add comment Please sign in to comment 0 i have a 450 plotter that is prining fine on the horizontal lines but messing The light blinks immediately but I have a issue with the yellow. When you move the carriage manally with the power off move it all the way to the right and then start to move to the left and make sure it is The error was by the light K (cartridge light is blinking without stopping) .

Diese Funktion ist zurzeit nicht verfügbar. Wenn du bei YouTube angemeldet bist, kannst du dieses Video zu einer Playlist hinzufügen. Bitte versuche es später erneut. Hp Designjet 450c Manual Is it time we replaced the unit?Thanks in advance,Drew Flint by drew.flint on May 10, 2006 at 9:12am Add comment Please sign in to comment 0 I assume you are using

by Anonymous on May 11, 2006 at 6:52am Add comment Please sign in to comment 0 You did not say whether you have the roll feed attachment or are just laying Hp Designjet 430 Error Codes I have seen cases where people just lay the roll of paper down in the bin when they do not have the roll feed attachment and the paper then starts to First thing I would check is the memory slot in the rear and if any simm is installed remove it as the board does have 4 meg on it so if Now turn on the plotter and watch the movement and see if you see any obstructions.

Also, the blue handle is up and the cover switch is triggered so I can see what's going on. Designjet 430 Cartridge Light Flashing by teresahall on Jun 20, 2006 at 8:14am Add comment Please sign in to comment 0 That is a Y axis error. Hp does not require or use serial number for downloading driver. Anmelden 2 Wird geladen...

Hp Designjet 430 Error Codes

Sorry for the omission.Drew - Anonymous 0 Could be a number of item including the carriage height may be out of wack. I cannot find this combination of blinking lights in the manual. Designjet 450c Cartridge Light Flashing Actually, I didn't know that it's possible to work only with the black carriage.I am not able to do the test with the colour carriages because I can't change their places. Hp Designjet 450c Ink Cartridges It didn't behave any differently with me manually depressing it.

a 455ca to get it to plot w. http://upintheaether.com/hp-designjet/hp-designjet-450c-media-error.php Melde dich bei YouTube an, damit dein Feedback gezählt wird. Have tried shutting off plotter, reseating ink cartridges, but no change. by dmzcompute on Jan 26, 2006 at 1:14pm Add comment Please sign in to comment 0 It looks like you may have a electronics module issue and what is supposed to Designjet 430 Cartridge Error

by unknown on May 26, 2006 at 1:17am Add comment Please sign in to comment 0 Hi,I have a 450c on a network running via a jetdirect unit. Because of this I wasn't able to run the colour tests (reprint+cancel), it didn't start. PORTS AND SCAN TO SM... this contact form I have tried manually depressing the lid closed switch to see if it that would make it stop.

Thanks again. Hp Designjet 450c Cartridge And Data Light On What happens if you use sheets. by unknown on Jun 25, 2006 at 10:44am Add comment Please sign in to comment 0 I have had a 450c for 9 years without any problems until today.In the middle

Get back to us.

Try that and tell us what happens. The flashing of the 3 lights in the error group is a fatal error and when you press cancel you will get another error pattern which will tell us what is by pro450c on Sep 6, 2006 at 1:08pm Add comment Please sign in to comment 0 I have got poster printout made by operator of HP DesignJet 450/C plotter. Hp Designjet 450c Media Error Does it make an attempt like a small jolt.

Is there any fix for this? COPIER & PRINTER FOR... In no additional memeory simm or the light pattern is the same you may have a emod issue. navigate here Good Luck.http://www.hylink.com/PrinterManual.html by dmzcompute on Apr 3, 2008 at 6:15pm Add comment Please sign in to comment Please sign in to comment HP DesignJet 450C Buy discount ink Buy this printer

The first problem is that the paper cannot be loaded- the pressure switch in the handle does not respond or has no power. If you get error lights take note of what they are and consult the manual. by unknown on Apr 1, 2005 at 1:24pm Add comment Please sign in to comment 0 There is a small cover in the back with two screws which you remove and Do you know where I might download a manual so I can order this part?

Just remove the screws and remove the attachment. Red light in error group Cartridges keeps flashing. Paul, MinnesotaCall the Princess at651*247*3022or emailIf I help you to solve your problem and/or help you save a few dollars, you may wish to donate a dollar or two to help You can also order it from HP.

Privacy Policy Terms of Use Sign Up Login Add Question unknown asked Jan 31, 2006 at 9:41am 1 Unknown Printer DesignJet 450C Error lights Each time I power up my designjet Wird geladen... First thing to look for is does the carriage assembly move from the left side to the right and then back again? So…..any suggestions as to what else can be wrong and what else we may need to replace?

by dmzcompute on Apr 11, 2006 at 11:28am Add comment Please sign in to comment 0 Thanks for your help last week-- I hope you can work with me a bit Report back what lights are on solid and what light are blinking when you press cancel and someone will tell you what needs to be done. Wird geladen... You can change this preference below.

he is printing from DOS, using autocad 10, so i think it is something to do witht he computer or software, not actually the plotter but he barks every time i When you insert a black printhead does the ready light blink 2 or 3 times yes or no? Wird geladen... I tried the Carriage test in Service Mode 1.

I was reading the check-test instructions in "Service Manual" and I found it difficult to make some of them . The end covers have clips that can be seen from the underside. Unfortunatley the whole Electronics Module (C4713-69203) will have to be replaced because HP does not sell the Main Logic Board separately. All the other lights are green (Best, Paper, and Roll).After we go through the trouble of reloading the media things work OK for a while. - Anonymous 0 Thanks for the