Home > Hp Designjet > Hp Designjet 430 Cartridge Data Error

Hp Designjet 430 Cartridge Data Error

World of HP Designjet Podcasts HP Instant Printing Pro Utility CONTACT US Our Terms & Conditions Returns Policy Copyright © 2016 HP Plotter. System Error: Steady EL - Faulty Cartridges. Fast LED - Line Sensor. Perform the Accuracy Calibration. Check This Out

Show more Language: English Content location: United States Restricted Mode: Off History Help Loading... What can I do if the Bail Mechanism Fails? Electrical Shock Hazard Serious shock hazard leading to death or injury may result if you do not take the following precautions: • Ensure that the ac power outlet (mains) has a Please try again later.

Reproduction or copying of images is prohibited. You can also look through our error codes which will tell you the basic problem with your printer e.g. Fast LED - Carriage-axis. To find out if one of the 4 cartridges is faulty I swapped the color cartridges, (not the black one), installing them one by one waiting for the ready light to

Thank you for watching! by matrujillo on Feb 28, 2005 at 9:52am Add comment Please sign in to comment 0 Are you absolutely sure you are installing the right cartridges? When cancel is hit, the following lights lite up blinking: cartridge,normal,load media,page and sheet. by dmzcompute on Jul 8, 2004 at 3:02pm Add comment Please sign in to comment 0 I have a designjet 430, after I installed four new cartridges, I power on the

First press the CANCEL button. Did you load media in correct orientation? Remove dirt from the slider rod and chassis beam. Also, if the carriage cannot find the true left stop during initialization (caused by interference), the engaging lever cannot be located.

Replace the Trailing Cable. The cam gear and engaging gear may not make correct contact with the left drive-roller gear even though the carriage is actuating the engaging lever. Replace electronics module. If the test fails, replace the Electronics Module.

Reach behind the front panel assembly and try to push the sensor towards the front of the printer (to release if stuck). http://www.dailymotion.com/video/xjou4x_designjet-450-repairs-cartridge-data-error_tech Go back to home and start over and start your own thread if you need to. by dmzcompute on Jun 18, 2004 at 1:37pm Add comment Please sign in to comment 0 With power off...i move carriage to far right side If i leave the top up Paul, MinnesotaCall the Princess at651*247*3022or emailIf I help you to solve your problem and/or help you save a few dollars, you may wish to donate a dollar or two to help

hp DesignJet 430, 450C and 455CA Printers Quick Reference Service Manual 7 Media-Axis (X-Axis) Test Purpose - Verify the operation of the components of the Media Axis. his comment is here Loading... If these keys are accidently pressed, you must immediately EXIT the Bench Run by switching OFF the Printer and powering ON again while pressing the Print Quality and Media Source keys. After initializing, error code "DLM" will appear because the Accuracy Calibration must still be performed. 12 Press the Cancel key and print the Demo Plot to check if the Printer has

K led (cartridges) is flashing, and the A, G and N leds are steady. Make sure that the trailing cable is positioned under the plastic tabs at the back of the carriage cover, and not above them. Designjet 450c (or 430) Cartridge + Data Error 12/9/2014 1 Comment One of the most common errors with the 400 series HP Designjet is the Cartridge + Data error. this contact form This will remove any dirt or ink that may be preventing a good connection.

Perform the accuracy calibration whenever the: • EEROM is erased. • Electronics module is replaced. • Drive roller is removed/replaced. • Media (X-axis) motor is removed/replaced. • Drive-roller gear is removed/replaced. david mcpike 1,913 views 0:49 HP Designjet 450C need HELP! - Duration: 8:49. All rights reserved. ©1990-2015 Autodesk User Group International, Inc.All Rights Reserved.

Can anyone point me in the right direction for fixing this type of problem?

The drive roller has shifted slightly from the expected position (mechanics). However, be careful not to jeopardize the print quality, which is very sensitive to the carriage angle. Transcript The interactive transcript could not be loaded. If so that is a mark encoder error where the printer can not find the white mark encoder on the left side of the platen.

Dirty or incorrect media. If problems persist, continue with replacing the Electronics Module. The Front Panel will then move from showing the Primary Error code to the Secondary Error code. navigate here If the Spittoon is loose or mispositioned, the cutter will have problems parking in the right cover.

DO NOT AT ANYTIME ENTER THIS TEST WHEN TROUBLESHOOTING THE PRINTER. And that's it. All times are GMT +0. It will be tight but should move.

What can I do if the Printer does not Power ON? Once the Cartridge LED goes to steady, continue with the remaining steps. Replace the Carriage Assembly. Faulty or badly connected X-axis Encoder Cable. 5.

Designjet Repair Help Designjet Drivers Designjet Error Codes Memory Upgrades User Manuals Videos & Podcasts Explore our Videos Explore our Podcasts 'Buy Right' Tools Designjet Upgrade Path HP Workstation Builder Buying Faulty media motor, or motor cable pinched. Dirty carriage flex circuit. Only when I install one of the color cartridges and the black one does the ready light does not flash.

If the test fails, an error code will appear on the front-panel. Electrical noise in motors. Film LED - Magenta Cartridge Continuity. Apply lubricant to the slider rod.