Home > Hp Designjet > Hp Designjet 1055cm Printhead Path Error

Hp Designjet 1055cm Printhead Path Error

Contents

Also, be sure not to load the media upside down. Hindol chowdhury 144,335 views 5:05 DesignJet 500 carriage and belt removal - Duration: 10:27. NOTE: If Removal and Installation instructions are needed for reference during any repairs performed; refer to the HP Designjet 5000 and 5500 Series Service Manual available on the Computer Care Web When I looked it the drive shaft had a black bulging built-up covering about 3 teeth.-rbc by unknown on Dec 16, 2009 at 12:11pm Add comment Please sign in to comment this contact form

I have ruled out the motor due to the above posts, but was also thinking about possibly replacing the carriage assembly. Sign in 11 0 Don't like this video? Have you tried with the power off to move the carriage assembly using the belt to see if the action is smooth the complete width of the plotter? If that is the case the belt will have to be replaced along with cleaning the motor shaft and the pulley.

Check Printhead Path Type 1

Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading... Also you will want to clean the surface of the drop detector and make sure there is no paper in the hole of the drop detector as that can cause issue, That said the most common especially when changing the belt or carriage assembly is not adjusting the carriage height with the special tool provided when you get a new carriage. Also you say you got the height tool, but did you use it according to the manual.

Contact HP Click here to contact HP customer support at http://welcome.hp.com/country/us/eng/support.htm. If the carriage moved correctly before the belt change, then I would lean towards you having put one of more connections in the wrong socket. inkproducts.com 126,486 views 16:40 HP Designjet 1050C Ink Tube Replacement Tutorial - Duration: 25:40. Hp Designjet 1050c Printhead Alignment Error NOTE: If the carriage does not move during the scan-axis test, replace the scan-axis motor (refer to pages 8-57 of the Service manual).

by unknown on Feb 11, 2008 at 5:21pm Add comment Please sign in to comment Hi shulesh, where abouts is this screw your talking about?? Check Printhead Path 2 I was reading a post on 5/6/08 8:42 PM and that's when I lost confidence. Open the door on the far right side, and pull the printhead cleaner tray to its forward-most position, checking for smooth and free movement. http://h30434.www3.hp.com/t5/DesignJet-Large-Format-Printers-and-Digital-Press/HP1050C-Printhead-path-Error-2/td-p/5067941 Now using the belt move the carriage assembly back a forth and look for smooth movement.

This procedure often solves the issue without requiring service. Hp Designjet 1050c Error Codes One connector is yellow and the other is red. Upon start up the plotter prompts the self test, and gives me the error code 0B0006, i've looked online and had no luck, and i've also called HP and was told The gold spring appears to be of wider diameter wire and seems stiffer and seems to be about the same length. ....perhaps the seemingly stiffer gold colored spring was utilized just

Check Printhead Path 2

Just telling us you get the message does not give us enough information to help especially if you have done all the thing we have told you to do. http://h30434.www3.hp.com/t5/DesignJet-Large-Format-Printers-and-Digital-Press/1055CM-quot-check-printhead-path-type-2-quot-replaced-motor/td-p/5050691 Fixed issue by:1) I cleaning off all the buildup on shaft use a tooth pick or other soft pick as a screw driver easily scores the slotted shaft. :(2) I went Check Printhead Path Type 1 by dmzcompute on May 10, 2008 at 3:59pm Add comment Please sign in to comment 0 Mine staying on the left and the noise comming from the belt not from the Hp Designjet 1055cm Check Printhead Cleaner Path I do this with all 1050 plotters I work on even if the belt is not changed since sometime the ledge that the carriage moves over warps just a bit over

If not positioned correctly the action will not be smooth the complete width but will hit a bump when the grooves change. weblink thanks - Reply 0 0 HP_user_fixer Student Posts: 1 Member Since: ‎05-03-2011 Message 4 of 7 (7,202 Views) Report Inappropriate Content Re: HP DesignJet 1055cm Error Code Options Mark as New If you cannot feel any obstruction the most likely cause is the tube assembly rubbing unevenly along the top. Bob Wert 17,450 views 25:40 HP DesignJet 1050 repairs - Replace print head - Duration: 2:41. Hp Designjet 1055cm Check Printhead Path Type(1)

Everything I said previous means nothing as this missing part is your issue. Only the cyan and magenta printheads appear to the left of the right end housing. If no media jam is detected, continue with Step 5. navigate here Chris Lee 3,564 views 2:01 HP Designjet 1050c Plus Black Ink Reseat Error - Duration: 2:58.

Loading... Hp 1055cm Belt You can clean them up and put a little grease along the top. If you get a bumping action, the problem is probably the belt is starting to wear and particles from the belt are adhering to the motor shaft and the belt will

Search the Community Entire ForumThis CategoryThis BoardUsers turn on suggested results Auto-suggest helps you quickly narrow down your search results by suggesting

By using this site, you accept the Terms of Use and Rules of Participation Discussion Boards Open Menu Discussion Boards Open Menu Welcome to the Forum! Working... Removing it will give you a better idea of the condition of the lines across the complete encoder strip. Hp Designjet 1055cm Plus System Error Codes Need help!Error Code: System error060308 00000008 ContactHP representativeWhat does this mean and or what do I need to do?

Reply 0 0 pbrooks259 Teacher Posts: 95 Member Since: ‎03-05-2012 Message 6 of 8 (3,882 Views) Report Inappropriate Content Re: 1055CM "check printhead path type (2)"--replaced motor twice, came back each does the carriage move at all before it gives that message? After research, reading the manual, and visual inspection I noticed the belt was worn and replaced it. his comment is here Any help would be Greatly appreciated.

Re-install the printhead cleaners, and push the printhead cleaner tray back into the printer. some one told me replace all printer heads as they are expired (date is old)...so I reaplced all new printer heads still I get same error same error....please help on this Most times with the tube assembly the carriage will always stop just short of going into the left side cover. Add to Want to watch this again later?

FixYourDesignJet 3,973 views 5:50 C6071-60177 HP 1050 1055 5000 5500 DESIGNJET - APPLICATOR + Oil - New From 1st Call 4 Service Ltd - Duration: 5:28. by dmzcompute on Dec 16, 2009 at 8:29pm Add comment Please sign in to comment 0 Dear Techs,I am struck last 6months with my plotter HP1055cm plus, I am having a For the carriage height can I just set it high and test to see if it actually is the height that is causing the problem?