Home > Hp Designjet > Hp Designjet 1055cm Plus System Error Codes

Hp Designjet 1055cm Plus System Error Codes

Contents

When removing the Service Station, make sure that you release... If the customer is using non-HP media with HP drivers, the colors in the required print may not be accurate. Page 156: Solving The Color Alignment Problem 4 Reprint the image you were attempting to print before (in the same Printhead Alignment mode) to see if the problem still exists. 5 To solve the problem, try the following: ■ Do NOT remove the Ink Cartridge while the Printer is Printing. http://upintheaether.com/hp-designjet/hp-designjet-1055cm-error-codes.php

System Error: Problem Description: Corrective Action: Try the following 0A0010 Problem in Pressurizing the Air System. HP DesignJets 1050C and 1055CM Printers Service Manual Figure 6: Vacuum Fan Removal and Installation... Conventions A small arrow => is used to indicate other parts of the Service Manual where you can find information related to the topic you are consulting. Page 121 6 Press the Enter key to begin a specific calibration when the required Service Calibration is highlighted.

Hp Designjet 1050c Service Manual

When the Calibration has finished, print a Service Config Print to verify the calibration is within the stated limits (Printer Setup Menu, Utilities, Test Prints, Service Config). Non-Continuable Error Codes do not allow you to continue working with the Printer, in this case power the Printer OFF and ON again and see if the System Error disappears. This can damage the printhead. Loosen the T-15 screw (item 1) securing the service station to the side of the printer.

To solve the problem, try the following: ■ Allow the print to absolute drying completion before stacking. If the Error Code reappears, then the EIO Card could be faulty. Do NOT use any other type of media apart from HP High Gloss Photo Paper. Hp Designjet 1050c Plus Parts Page 214: Front Panel Assembly (item 1) and cable clamps (item 2) inside the Right Hand Cover (item 3) (Refer to Figure 2).

To find the humidity level, print the Service Configuration Print (Printer Setup Menu I Utilities I Test prints I Service config). 1-12 HP DesignJets 1 050C and 1 055CM Printers Service Hp Designjet 1050c Owners Manual Thank you! Register · Log In HP Support Forum Home > Printers > Inkjet > HP DesignJet 1055cm Error Code HP Support Forums Join in the conversation. Please try the request again. Mode Baud Sel. 4-42 HP DesignJets 1050C and 1055CM Printers Service Manual...

Switch the printer ON again. Hp Designjet 1055cm Plus Parts Page 69: Printhead Status Messages While Printing The printer can still operate with a printhead that needs replacing. HP DesignJets 1050C and 1055CM Printers Service Manual... Perform the Electronic Systems Test => Page 4-5.

Hp Designjet 1050c Owners Manual

This is because the part of the print exposed to the air is always lighter than the covered one. Press ENTER to continue 5-14 Back Press Enter Enter HP DesignJets 1050C and 1055CM Printers Service Manual... Hp Designjet 1050c Service Manual Also inspect ALL Ink Cartridges for any signs of leaking (the bottom valve of the Ink Cartridge will contain ink). Hp Designjet 1055cm Network Configuration Service Station Color to Color Calibration HP DesignJets 1050C and 1055CM Printers Service Manual Removal and Installation Page 5-11.

Using this procedure you will be able to determine exactly which component failed. his comment is here If the Error Code reappears, then report the error to the HP response Center or the nearest HP Support Office, stating the following information. Page 72 Carriage Assembly is faulty. EEROM Utilities EEROM will be tested. Hp Designjet 1055cm Plus Troubleshooting

Faulty APS Sensor or APS Pump. Electronics Module 2. If the Error Code reappears, then report the error to the HP response Center or the nearest HP Support Office, stating the following information. http://upintheaether.com/hp-designjet/hp-designjet-1055cm-plus-error-codes.php Page 145 7.

Remove the left side cover (see Figure 5).Figure 5: Removing the left side cover.Removing the Multi-Roll feeder right side cover WARNING: Turn both the printer and the Multi-Roll feeder Off and Hp Designjet 1055cm Parts Electronics Module Code: 00XXXX:0000XX Code: 00XXXX:0000XX Page 8-20. Release Info 4-32 3.

Contact HP?

Printer Model Type 5. HP DesignJets 1050C and 1055CM Printers Service Manual... Cut Sheet rice paper loading failure Thin rice paper is sucked into the Center Platen grooves and Linear Blade Ridge. System Error 060308 00000008 Pen to Paper Spacing 5-15 6.

Page 28 Troubleshooting 1-16 HP DesignJets 1050C and 1055CM Printers Service Manual... Possible causes are the Drop Detector or Service Station being previously replaced and the necessary calibrations not being performed. w o Si HP DesignJets 1050C and 1055CM Printers Service Manual 1-17 Troubleshooting B £ 1 1 >> o o c3 OS 1 o Q u Oh „ §| < T3 navigate here There are more folks there with Designjet experience.

Scan Axis HP DesignJets 1050C and 1055CM Printers Service Manual Service Tests and Utilities Back Make Selection Press Enter Enter 4-17... Press ENTER to continue 6 If the calibration fails Perform the Electronic Systems Test 4-5. Page 150: Print Quality Troubleshooting Checklist To clarify if the reason of the problem is related with the print mode defined with the Non-HP Driver try the following: Print the same WARNING Only replace one component at a time and check if the error has gone before replacing another component.

Lift the Pinch wheels (using the Media Load Handles) and pull the media clear. 3 Replace media spindle if broken. 4 Replace the Paper-Axis Motor => Page 8-12. That allows the dye to migrate through the coating and causes bleeding. Following initialization, insert one printhead starting with the black printhead. Continuable and Non-Continuable Error Codes Some of the Error Codes are continuable, which means you can press Enter on the front-panel and continue working with the Printer.

This color variability among different HP DesignJet Series Printers has been always present. Page 10: Table Of Contents Moisture on the Printer 9-2 Noisy Carriage Bushing 9-2 Belt Swelling 9-2 Cleaning the Printer 9-2 General Cleaning 9-2 Cleaning the Overdrive 9-3 Scheduled Maintenance 9-3 I Top ■ Back ■ .