Home > Hp Designjet > Hp Designjet 1050c System Error

Hp Designjet 1050c System Error

Contents

All rights are reserved. If necessary, clean Encoder Strip using a damp cloth. 1-8 HP DesignJets 1050C and 1055CM Printers Service Manual Troubleshooting Problems with the Vacuum Fan If you have problems loading either Roll Check firmware in Utilities / Statistics / Code rev. ■ The complete error number (See Note below). ■ The Service Configuration Print => Page 1-19 ■ The Current configuration sheet. ■ To verify if there really is a problem with the Vacuum Fan, try the following: With the Printer ON, open the Window of the Printer and place a sheet of HP http://upintheaether.com/hp-designjet/hp-designjet-1050c-plus-system-error.php

PRINTER LIMITATION - NO SOLUTION AVAILABLE. Sign in to report inappropriate content. I Enter Printer setup options IPen settings ... This color variability among different HP DesignJet Series Printers has been always present. find more info

Hp Designjet 1050c Service Manual

Before turning the printer on, check the resistance (ohms) between the two test points above the Trailing cable. This implies that the friction between the Center Platen and the rice paper becomes higher than between the Overdrive wheels and the paper. Turn the printer off, then on and attempt to verify functionality. Select Full (if needed) and press the BACK key to return to the main menu.

Make sure to properly connect the Trailing cable or replace a shorted Trailing cable before installing the new fuse.Troubleshooting stepsIf any of the troubleshooting steps listed below solve the problem, attempt Calibrations Backup NOTE: Printer menu mode must be set to Full to access the Service Tests submenu. Velocity Shutdown (2) 1 Open the Window and check for any visible obstacles restricting the movement of the Carriage Assembly. Hp Designjet 1055cm Network Configuration Advertisement Autoplay When autoplay is enabled, a suggested video will automatically play next.

If no error appears, attempt to verify functionality. Using this procedure you will be able to determine exactly which component failed. 2-16 HP DesignJets 1050C and 1055CM Printers Service Manual System Error Codes System Error: Problem Description: 0C0032 (Continuable) Try the following: ■ Make sure that the Ambient temperature is within the allowed range (between and 55 Degrees Centigrade). ■ Replace the Electronics Module => Page 8-25. http://www.computercarefiles.com/TWI_Docs/bpp90152/default.html Service Station 5-11 4.

Demos ... Hp Designjet 1055cm Plus Troubleshooting The Carriage is at the incorrect height in relation to the Center Platen. Removing the multi-roll feeder left side cover WARNING: Turn both the printer and the multi-roll feeder off and disconnect them from the power source prior to performing any maintenance. The failure modes "media jam" and "head crash" are grouped together because in many cases a media jam causes the media to lift up into the carriage path and cause a

Hp Designjet 1055cm Error Codes

If the error continues after replacing the Firmware and replacing/verifying the Vacuum fan, replace the Electronics module (refer to pg. 8-25 of the 1000 Series Service Manual for "A" Models) (Refer check my blog NOTE: Only ONE CE needs to be dispatched to perform service on a 1000 Series printer attached to a Multi-Roll feeder.Removing the Multi-Roll feeder left side cover WARNING: Turn both the Hp Designjet 1050c Service Manual Restore password × Upload manual upload from disk upload from url Thank you for your help! Hp Designjet 1055cm Plus System Error Codes Figure 8: Rear Top cover.

HP DesignJets 1050C and 1055CM Printers Service Manual 2-7 System Error Codes System Error: Problem Description: 04Cxxx EIO Accessories (EIO Card/Hard Disk Drive) Error. his comment is here NOTE: Do not use Clear Film, Vellum or Natural Tracing paper when performing a Pen Alignment Calibration. Replace the electronics module (refer to pages 8-25 of the Service Manual for "A" models) (Refer to Supplement for Main PCA Replacement on "B" Models). How to Print the Service Configuration Print 1 Load media (Roll media or at least an A4 Sheet) into the Printer. 2 Once the message "Ready" is displayed on the front-panel, Hp Designjet 1050c Owners Manual

Only replace one component at a time and check if the error has gone before replacing another component. Remove the left door. If the error appears following replacement of all suspected printheads, contact HP. this contact form Performing the Necessary Service Calibrations Is the printer calibrated correctly after replacing a component?

If Ink Limiting is OFF, turn it ON. ■ Change the paper margins to 15mm, either in the Front Panel or in the Driver. System Error 060308 00000008 Printer Model Type 4-35 5. This is because the part of the print exposed to the air is always lighter than the covered one.

Pen Alignment 5-22 Carriage Height Calibration 5-24 HP DesignJets 1050C and 1055CM Printers Service Manual Table of Contents Print Quality 6-1 Print Quality Troubleshooting Checklist 6-2 Print Modes 6-3 How to

Replace the complete APS => Page 8-20. If the fan cannot be heard replace the Vacuum fan (refer to pg. 8-11 of the 1000 Series Service Manual) and repeat steps 1-8. Refer to pgs 8-44, 8-39, and 8-25 of the Service Manual. Hp Designjet 1055cm Plus Parts Using this procedure you will be able to determine exactly which component failed. 010050 XXXXXXXX (Non-Continuable) PostScript Processing Error.

Open the left door of the Multi-Roll feeder. The cable test points should show no continuity, which translates to a very high resistance on the multi-meter. Unclog any holes with a straightened paperclip or other appropriate tool. navigate here To solve the problem, try the following: ■ Reduce the level of humidity (<65%) that the Printer is working in.