Home > Hp Designjet > Hp Designjet 1050c System Error 0b0006

Hp Designjet 1050c System Error 0b0006

Contents

Always check the contacts to make sure they are straight and not separating from the ribbon cable. Remove and reinstall the cable again and measure the resistance. Pings ok. The same is true at the carriage end but usually it is at the emod connection where the trouble is. http://upintheaether.com/hp-designjet/hp-designjet-1050c-plus-system-error.php

Reply With Quote Quick Navigation HP Top Site Areas Settings Private Messages Subscriptions Who's Online Search Forums Forums Home Forums System Forums System Announcements Site Feedback & Questions Newbie Check In! Resources LPS Computer: 1050C Owner's Manual HP: Support Case Manager You May Also Like Repair Error 388 on the HP Officejet 7130 The HP Officejet 7130 is an all-in-one printer with My understanding is there are some very tiny fuses more than 1 that blow on the board not protected by a fuse in a holder and in that case the board My boss thought he'd be helpful and wound up de-laminating the contacts on the end of the trailing cable.

Hp Designjet 1055cm Error Codes

Check that Corrective Action: the ends of the Trailing Cable are flat and are not damaged or bent. Bob Headrick, HP ExpertI am not an employee of HP, I am a volunteer posting here on my own time.If your problem is solved please click the "Accept as Solution" button------------VIf WARNING TAKE CARE WHEN CONNECTING THE TRAILING CABLE TO THE ELECTRONICS MODULE OR CARRIAGE.

This machine is the "A" model. Power ON the Printer and check if the Error Code disappears. Remove the right door and front top cover from the multi-roll feeder (follow steps 1 through 5 of the previous section and remove the right door instead of the left). Hp 1050c Trailing Cable If the fuse is NOT blown (value less than 1 ohm), replace the Carriage and Trailing cable (refer to pgs. 8-44, and 8-39 of the Service Manual).

If not maybe you can get ahold of a good tech at HP who knows his stuff and can get you the proper fuse and the schematic for the repair. Hp Designjet 1055cm Plus System Error Codes INCORRECT INSTALLATION WILL BURN THE FUSE IN THE ELECTRONICS MODULE, CAUSING THE COMPLETE FAILURE AND REPLACEMENT OF THE LOGIC BOARD. 100 OHMS OR HIGHER MUST BE SEEN AT THE TEST POINTS. the fuse is at the top of the ops board, on the right side, in the back. http://www.computercarefiles.com/TWI_Docs/bpp90152/default.html Just bring the old one in.

If the error appears, turn the printer off and disconnect the power cable from the printer. System Error 060308 00000008 Wait 60 seconds. Instructions for multi-roll disassembly are listed at the bottom of this document for reference. HP Designjet 5000 5500 parts May 21, 2014 | HP DesignJet 1050c plus InkJet Printer 1 Answer No power to hp design jet 110 check the internal power supply board connection

Hp Designjet 1055cm Plus System Error Codes

Add × Loading... http://www.copytechnet.com/forums/hp/41572-hp-designjet-1050c-plotter.html Powered by vBulletin Version 4.2.2 Copyright © 2016 vBulletin Solutions, Inc. Hp Designjet 1055cm Error Codes Scroll to Accept and press Enter. Hp Designjet 1050c Service Manual out of box M Get Weekly DIY Guides & Inspiration Life Made Easier.

I noticed you posted the same question to the HP forums. his comment is here by nivek on Nov 21, 2010 at 8:16pm Add comment Please sign in to comment 0 Do not know but you can buy them from any good electronics store. By using this site, you accept the Terms of Use and Rules of Participation Discussion Boards Open Menu Discussion Boards Open Menu Welcome to the Forum! Following the calibration, turn the printer off then on and verify functionality. Designjet 1055cm Trailing Cable

Restore password × Upload manual upload from disk upload from url Thank you for your help! It will be a very small fuse. Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. http://upintheaether.com/hp-designjet/hp-designjet-1050c-system-error.php The last cable I had to replace, lucky for me had the fused emod since even with all the times I have done it, this time I made a mistake and

Thank you! Register ยท Log In HP Support Forum Home > Printers > DesignJet, Large Format Printers and Digital Press > DJ 1050C 0B0006 error HP Support Forums Join Technical Forums Copier Technical Discussion Canon Konica Minolta Kyocera Mita, Copystar Muratec Panasonic Ricoh, Savin, Gestetner, Lanier Sharp Samsung Toshiba Xerox Other Copier Brands Fax & Printer Technical Discussion Brother Canon Become part of our maker community.

Anymore info you might have on this?

I'll now adjust my pricing and time to reflect my new experience with this belt replacement.Thanks again.Tom by RoverLRC on Dec 1, 2008 at 3:26pm Add comment Please sign in to I STILL have continuity. If the resistance is greater than 100 ohms, change the fuse (if present), turn the printer on and verify functionality. by RoverLRC on Nov 21, 2008 at 10:20am Add comment Please sign in to comment 0 Thank you very much DMZ Nivek and the others who have posted tipswithout this help

The fuse is rated at 10A. HP DesignJet Printers &... References HP: DesignJet 1000 Printer Series Promoted By Zergnet Comments Please enable JavaScript to view the comments powered by Disqus. navigate here Connect a new trailing cable to the carriage and electronics module, but do not remove the first one.

Respond to this 0 Just went thru this!! All rights reserved. Other than inspecting the sockets on the mainboard for debris, I don't have any other ideas. There are also two posts on either side where you can use a ohm meter where you should get a reading which will slowly go back down to 0.

But not a very good solution. Check that the ends of the cable are flat and not damaged or bent. Verify printer functionality. HP DesignJet Printers &...

If the error continues after reinstallation of the Trailing cable and replacement of the fuse (if applicable), then replace the Electronics module and Trailing cable (if not already replaced). If no service has been performed and printer was working normally before the error occurred, continue with the section Steps for printer working normally prior to error listed below. Its been years and I went back and checked my documentation and couldnt find the fuse electronic specs. Browse Categories Answer Questions HP DesignJet 1050c InkJet Printer HP DesignJet Printer and Copier HP Printer and Copier Printers & Copiers All Unanswered Join Sign In Ask a Question × HomeForumPrinters

Problem Description: Replace the Electronics Module Corrective Action: 2-20 TAKE CARE Make sure that the Vacuum Fan is connected correctly to the Electronics Module. Hi here is HP'S explanation for System Error 0B0006 The Trailing cable has been incorrectly connected. NOTE: If Removal and Installation instructions are needed for reference during any repairs performed, refer to the 1000 Series Service Manual available on the Computer Care Web site for review Then check it for obvious kinks, wear points or other physical damage.

You will need to entirely replace the old logic board with a new one. When I took the carriage back apart I noticed the cable had lost the stiffening pieces on the end. I did ruin the trailing cable and ordered another one. This error code indicates that the 5VDC and ground are shorted together by the trailing cable.