Home > Hp Designjet > Hp Designjet 1050c Plus System Error

Hp Designjet 1050c Plus System Error

Contents

Ink Pressure System 4-14 5. The best test you can do is with the power off open the cleaner door on the right and pull out the cleaners. by Freak on May 25, 2008 at 5:22pm Add comment Please sign in to comment 0 All I know is when a new cleaner is installed the carriage assembly moves over System error 85:10 Paper-axis shutdown (during the paper advance test). http://upintheaether.com/hp-designjet/hp-designjet-1050c-system-error.php

Uploaded on Mar 1, 2011Basic maintenance to overcome the 'Check printhead path' error message on the DesignJet 1050 & 1055 series.If the fault persists following this you are likely to require Cut Sheet rice paper loading failure Thin rice paper is sucked into the Center Platen grooves and Linear Blade Ridge. This is a very important step to remember because if this is not done, the media may be loaded at an angle, causing the media to be rejected. ■ Perform the The door is closed.

Hp Designjet 1055cm Error Codes

Repeat steps 1-8, if problems persist continue with the remaining steps. System error 61:04 Firmware error. Corrective Action: Try the following: ■ The leak detector could have been triggered due to condensation in the Printer.

System error 56:10 Drive roller encoder sensor error. Companiesthat utilize our service department Fixed at your location onsite Design Jet 1050C plotter service includes troubleshooting, inspecting, cleaning! Design Jet 1050C Error Messages HP Design Jet 1050C/1050C PLUS Plotter Error Codes HP DJ 1050C system error 01:10 A problem with the Electronics module has occurred. Hp Designjet 1050c Error 060308 00000008 Sign in to make your opinion count.

HP DesignJets 1050C and 1055CM Printers Service Manual 1-9 Troubleshooting Printhead Crashes/Smears on High Density Prints Using Coated Media High density prints can cause cockle mainly on HP Coated Media. Hp Designjet 1050c Service Manual The paper should load over the roll toward you. ■ The paper may be loaded at an angle. There was no weird noises before and I'm just not feeling comfortable right now disassembling the printer. http://www.computercarefiles.com/TWI_Docs/bpp90068/default.html I was reading a post on 5/6/08 8:42 PM and that's when I lost confidence.

Only replace one component at a time and check if the error has gone before replacing another component. Hp Designjet 1050c Printhead Thank you! Register · Log In HP Support Forum Home > Printers > DesignJet, Large Format Printers and Digital Press > DesignJet 1050C plus - Error 00340E:000002 HP Support CAUTION The Caution symbol calls attention to an operating procedure, practice, or the like, which, if not correctly performed or adhered to, could result in damage to or destruction of part Corrective Action: Try the following: WARNING System Error: Problem Description: Corrective Action: NOTE ■ Check that the Service Station Encoder-Cable is NOT broken or damaged. ■ Check that the Service Station

Hp Designjet 1050c Service Manual

Problem Description: Try the following: Corrective Action: n n n n n WARNING Only replace one component at a time and check if the error has gone before replacing another component. click to read more f Reinstall the Hard Disk Drive correctly, making sure that the two installation screws are completely tightened. Hp Designjet 1055cm Error Codes Just telling us you get the message does not give us enough information to help especially if you have done all the thing we have told you to do. Hp Designjet 1055cm Plus System Error Codes Once it goes to initialization the carriage goes to the end of the track where the cartridges are and stops.

Do I need this tool (C6071-60166) in the black printhead slot to make any height adjustments? his comment is here If the belt is not positioned correctly, then the wrong inside of the belt could be over one of the items causing a path error. It usually accumlates a large amount of cyan ink and use a lint free cloth dampened in plain water. Then open the door on the right and the unit should be sitting to accept the cleaners. System Error 060308 00000008

Contrast ... Open the Rear Top cover (see Figure 8). The Carriage is at the incorrect height in relation to the Center Platen. this contact form Faulty APS Sensor or APS Pump.

CALL TODAY TOLL FREE!1-800-836-9287 Home | Printer Repair Services | Plotter Maintenance Services | Online Service Request Service Contracts | Printer Drivers | Contact Us | Privacy Statement | Useful Links Hp Designjet 1050c Driver Do so using the belt to move the carriage and see if you get any bumping or other action when it reaches the area you are having problems. This effect make it almost impossible to load the rice paper correctly because the Vacuum is too high.

Occupy Wall Street TV NSA Clip Library TV News Top Animation & Cartoons Arts & Music Community Video Computers & Technology Cultural & Academic Films Ephemeral Films Movies Understanding 9/11

Banding due to Ink Cartridge replacement while printing A user has removed the Ink Cartridge while the printer was printing, which has caused the printer to stop. Switch the Printer OFF and ON again and wait for the initialization. Power OFF the Printer from the back and disconnect the power cord. Lps Computer I assume you are putting them in the right slots as each color has it own slot.

Switch the Printer ON again. When the tool is inserted you move the carriage assembly using the belt back and forth and if you hear any sort of a rubbing or squealing sound then the carriage To verify, at the Ready prompt, scroll to the PRINTER SETUP icon, and press ENTER. navigate here This causes two main problems: 1.

by dmzcompute on May 9, 2007 at 2:44pm Add comment Please sign in to comment 0 Hi.... Since this is the plus model you have a hard disk inside the back of the printer.