Home > Hp Designjet > Hp 5500 Error Messages

Hp 5500 Error Messages

Contents

Other operating systems NOTE: If the System Maintenance Utility has been downloaded correctly from www.Designjet.hp.com but problems arise while upgrading printer firmware via the System Maintenance Utility, another download is not CAUTION: Do not turn power off or unplug the printer until prompted on the front panel display. top System Error 0B0005 (non-continuable) Explanation Air Pressurization System (APS) failure. The front panel will display Firmware Upgrade. http://upintheaether.com/hp-designjet/hp-designjet-5500-error-messages.php

Loosen the two thumbscrews that attach the HP Jetdirect EIO card. On the left navigation bar, select technical support. Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. Turn the printer on.

Hp Designjet 5500 Printhead Reseat Error

To see information on a specific printhead color, press the ARROW keys until the front panel highlights that color (see Figure 9), and then press the ENTER key. Double-click the printer to be upgraded. If you have an active support agreement or HP Care Pack, you can link them to your profile to ensure access to all services. top System Error ffff ffff 030d0171 Explanation At power up, the printer thinks it is smaller than 42 inches.

Click here for information on contacting HP Customer Care. Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. If the error continues, call HP for technical support to troubleshoot the problem. Hp 5500 Printhead Problems If the problem persists following the upgrade, replace the lens cover: Scroll to the Printer Setup Options icon and press the Enter key.

If no error occurs, plug the network cable back into the network card and attempt to print (problem may have been caused by receiving information through the port during the power Hp Designjet 5500 System Error Codes top System Error 0D0002 (continuable) Explanation Insufficient memory to initialize HP-GL2/RTL Recommended action Minimum required memory is 96 MB. If you press any key on the front panel ffff ffff 03450097 may be displayed. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpp02990 Click here for instructions on how to upgrade the printer's firmware .

Disconnect the data cable from the printer (network or parallel). Hp Designjet 1050c Error Codes The current status of the printhead. Do you wish to proceed to the home page of the new product? Open the printer's window.

Hp Designjet 5500 System Error Codes

Follow the troubleshooting steps listed below. see it here If the error re-occurs or the problem persists, turn the printer off and continue with the remaining steps. Hp Designjet 5500 Printhead Reseat Error Turn the printer off using the main power switch at the back of the printer. Hp Designjet 5500 Service Manual System Error 0B0002 (non-continuable) Explanation Bad IDS pressure reading.

Reseat or add memory (if needed). navigate here Click here for instructions on how to upgrade the printer's firmware . Scroll to Clean Platen and press Enter. Please try the following:Use a different search stringIf search was based on document ID, check document ID or switch to keyword search Change your search criteria selectionCheck your search string for Hp Designjet 5500 Printhead Error Codes

Remove and reinstall the EIO card. Open the cover on the back of the printer to access the ink cartridge assembly (right side of the printer, looking from the back). If the tubes system is priming: install setup printhead(s) Ensure that HP No. 81 printheads are installed. Check This Out System Error 010092 (continuable) Explanation The Mark Encoder position is not detected on the Drive roller.

Using the Arrow keys, scroll to Utilities and press Enter. Hp Laserjet 5500 Error Codes Recommended action Turn the printer off (using the power switch at the back of the printer), and wait 15 minutes. Click here for information on how to replace the Lens cover .

If the error continues, call HP for technical support to troubleshoot the problem.

System Error 0FXXXX (non-continuable) Explanation An error with the firmware has occurred. Attempt to print. Using the Arrow keys, scroll to Utilities and press Enter. Hp Designjet 5000 Service Manual Modify your browser's settings to allow Javascript to execute.

Click here for information on how to download media profiles . If the error continues, call HP for technical support to troubleshoot the problem. If the error does not come up at that time, it is most likely related to the network. http://upintheaether.com/hp-designjet/hp-5500-error-codes.php Recommended action Press ENTER on the printer's front panel to continue (the printer will still function, although the heater will be disabled).