Home > Hp Designjet > Hp 5500 Error Codes

Hp 5500 Error Codes

Contents

Replace the APS Page 8-65. Replace printhead cleaners when printheads are replaced. New supplies should be obtained and made ready to replace the color indicated. top Status codes and messages The status code is made up of 4 digits: the first two digits represent the HP ID code that identifies the consumable and its color. Check This Out

Corrective Action: Try the following: Recommend to the customer to print via the Network Card because the transmission time via the Parallel Port is very slow. Nächstes Video HP Designjet 5500ps Check Printhead Cleaner Path Error - Dauer: 2:36 Zeb Harris 14.385 Aufrufe3 2:36 Designjet 5500 Belt Replacement & Calibration - Dauer: 29:55 Bob Wert 16.367 Aufrufe35 System Error: 0B000C Problem Description: Serial Device ADC test failure. Replace the Drop Detector Assembly Page 8-70. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpp03771

Hp Designjet 5500 Service Manual

Wenn du bei YouTube angemeldet bist, kannst du dieses Video zu einer Playlist hinzufügen. Ensure that you have the correct ink cartridge. Ensure that the ink cartridge is the correct color for that slot. Corrective Action: Try the following: Check all the cables of the APS and make sure they are correctly connected and are NOT damaged.

A status messages consists of a code and an action message (See Figure 1): Ink displays information on the ink cartridges. Clean the electrical contacts on the Carriage and the Printheads using a lint-free cloth dampened with water. Corrective Action: The minimum memory required is 96 Mbytes so verify memory installed on the printer using the Statistics menu (refer to the User's Guide). Hp Designjet 1050c Error Codes System Error: ffff ffff 031609xx Problem Description: This error code only appears if the Main PCA was replaced without removing the media from the Printer, because the firmware tries to find

Power ON the Printer and check if the Error Code has disappeared. Hp Designjet 5500 Printhead Reseat Error Turn the printer off and remove the power cable from the back of the printer. System Error: 0C0030 Problem Description: Drop Detector Failure. https://www.orionmarket.com/product_error_page.aspx If the New Vacuum Fan does not function correctly either, then replace the Main PCA Page 8-79.

Replace the APS Page 8-65. Hp Designjet 5500 Manual Pdf Attempt the recovery procedure listed below. 2. Quality, Productivity, or Max. The first digit in the ID code (see table below) identifies the consumable, and it provides specific consumables information.

Hp Designjet 5500 Printhead Reseat Error

Open the top cover.

Corrective Action: Try the following: Check the APS for any signs of Ink. Hp Designjet 5500 Service Manual the correct model, are normal printheads not setup printheads. Hp Designjet 5500 Printhead Error Codes NOTE After replacing the Main PCA, make sure you perform the Backup EEROM Page 4-31, making sure that you select "Main PCA" when prompted.

System Error: 050001 (Continuable) Problem Description: Lens has problems reading the Mark Encoder on the Drive Roller. his comment is here Which software application the customer is using (name, version, etc.). Using this procedure you will be able to determine exactly which component failed. top Ink cartridge errors (first digit = 6, 8) When replacing ink cartridges, do the following: Use Replace Item in the Ink Cartridges menu. Hp 5500 Printhead Problems

NOTE If the error code appears again, try connecting the Printer to a different power socket. Corrective Action: Try the following: Check that the Service Station Cable (the grey flat cable with the grey connector) is plugged into the Main PCA, and that the clips of the XX11 Replace Incorrect type of printhead installed. this contact form Melde dich an, um unangemessene Inhalte zu melden.

CAUTION: Do not remove the setup printheads from the carriage assembly without following the procedures in the setup guide. Hp Designjet 5500 Air In Tubes WARNING Only replace one component at a time and check if the error has gone before replacing another component. due to a temporary loss of tension).

Check that the Paper-Axis Motor cable is correctly connected.

The following table describes the messages and status codes for ink cartridges, and the recommended actions. A new ink cartridge is required. If the error does not appear again, then the problem may have been that the Printer was receiving some information through the port while powering-up. Hp Designjet 5000 Service Manual System Error: 0B0002 Problem Description: Bad IDS pressure read.

Ensure that the printhead cleaner is the correct color for that slot. If the two LED's are ON and the error continues, replace the Main PCA Page 8-79. System Error: 0C00FF Problem Description: Print Mask could not be generated. navigate here Wird verarbeitet...

Corrective Action: Try the following: Check the APS Sensor and the valve cables, making sure that they are NOT damaged and connected correctly. System Error: 0D0000 (Continuable) Problem Description: No Media Profiles Available. For 3rd party LAN Cards, the HP support organization should communicate to the customer that they should address it through the 3rd party vendor support structure. The printer stops.

Possible causes are memory corruption, print mode definition incompatible with mask restrictions (if using an external RIP). Even if the error appears again, there is nothing wrong with the printer 63 Designjet 5000 / 5500 0F0100 03180382 error (Non-Continable) After cutting the media, the Printer cannot deactivate the cutter 64 Replace/reseat troubleshooting steps Turn the printer on. Wähle deine Sprache aus.

Corrective Action: Try the following: Check all the cables of the APS and make sure they are correctly connected and are NOT damaged. Possible causes are memory corruption, print mode definition incompatible with mask restrictions (if using an external RIP). It always happens during initialisation, while checking the printhead cleaners. If the Error Code continues, replace the Main PCA Page 8-79.

Connect a New Vacuum Fan to the Main PCA and power ON the Printer. XX16 Replace The printer was printing: printhead short Select Yes to replace printheads or No to finish print job without the failed printhead (print quality is affected). Open the Carriage cover and remove all the Printheads. System Error: 0A0010 Problem Description: APS Failure.

The following table describes the messages and status codes for printheads, and the recommended actions. Remove the Drop Detector and make sure that there are no obstacles inside which are blocking the sensor. In most cases, it is a problem of incorrectly inserted printhead cleaners, but it can also be caused by the service station. 41 Designjet 5000 / 5500 0B000A error Primer Shutdown The time (hours) the printhead has been operating in the printer.