Home > Hp Designjet > Hp 5500 Designjet Error Codes

Hp 5500 Designjet Error Codes

Contents

Click here for information on contacting HP Customer Care. top System Error 0C0030 (non-continuable) Explanation Drop Detect failure. due to a temporary loss of tension). Plug in the network cable (if not already plugged in). have a peek here

Tags: designjet 5000, error code 5000, 5500 No feedback yet Comment feed for this postComments are closed for this post. Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. This error code appears when the Printer detects that the same area of nozzles do not work in different Printheads. System Error Codes consist of two groups of alphanumeric characters: [XXXXXX]-[YYYYZZZZ].

Hp Designjet 5500 Printhead Reseat Error

top System Error ffff ffff 030d0170 Explanation At power up, the printer thinks it is smaller than 42 inches. If the error re-appears, call HP for technical support to troubleshoot the problem. Open the cover on the back of the printer to access the ink cartridge assembly (right side of the printer, looking from the back). Generated Mon, 17 Oct 2016 21:39:26 GMT by s_ac15 (squid/3.5.20)

If no error appears, attempt to verify printer functionality. Click here for information on contacting HP Customer Care. Install a new lens, and follow the remaining instructions provided by the printer. Hp Designjet 5500 Air In Tubes If everything looks ok, perform a cold reset on the Jetdirect card (through the front panel).

Check that the Air Pressurization System Sensor Cable is correctly connected and is NOT damaged. Remove and re-install all six ink cartridges and press ENTER to continue. Generated Mon, 17 Oct 2016 21:39:26 GMT by s_ac15 (squid/3.5.20) ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection try here Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on.

If the error code continues, replace the PCA Page 8-79. Hp Designjet 5500 Manual Pdf Clean the Mark Encoder on the Drive Roller using the Turn DRIVE ROLLER Utility Page 4-18. Power ON and check if the System Error Code has disappeared. Attempt the Recovery procedure. 2.

Hp Designjet 5500 Service Manual

HP Designjet 5500 From the above location, type copy /b DJ5500_Axxxx.FMW LPT1 (the xxxx refers to the most current firmware revision).

None Insert There is no Ink Cartridge or printhead installed. Hp Designjet 5500 Printhead Reseat Error If the customer has this problem frequently, recommend upgrading the firmware revision to A.02.xx in order to lower the frequency of the error. Hp 5500 Printhead Problems Send the copy command from the PC (press Enter on the keyboard), which will send the firmware upgrade file (typed in during Step 1) to the printer.

top System Error 0B0004 (non-continuable) Explanation Air Pressurization System (APS) failure. http://upintheaether.com/hp-designjet/hp-designjet-5500-error-messages.php If requent, upgrade firmware to A.02.xx 3 Designjet 5000 / 5500 ffff ffff 01dcxxxx error There is a problem with the I/O Card (happens during power up) 4 Designjet 5000 / top System Error 0C00FF (non-continuable) Explanation Print Mask could not be generated. Recommended action HP recommends printing via the network card because the transmission time via the parallel port is very slow, which may be causing the error. Hp Designjet 1050c Error Codes

NOTE: This problem only appears when upgrading from Non-UV ink firmware to UV ink firmware while the media is loaded. Follow up: If you have an error code which is not documented in this Service Manual or you have an error which you cannot resolve, then report the error to the WARNING Only replace one component at a time and check if the error has gone before replacing another component. Check This Out Replace the Drop Detector Assembly Page 8-70.

Open the folder when prompted, once the download is complete. Hp Designjet 5000 Service Manual Type cd HP Designjet System Maintenance, and press Enter again. System Error: 0B000B Problem Description: APS Failure.

The printer will display the following messages: Lift the Window, Clean Roller Mark, Replace Lens, and Lower the Window, and press ENTER to continue.

Replace ONE Ink Cartridge at a time, checking if the System Error Code disappears. If error appears again, Call HP Support top System Error 0D0005 03180382 (non-continuable) Explanation The printer cannot deactivate the Cutter after cutting the media. Re-install the DIMM(s) into the memory slot(s). Hp Designjet 5100 Error Codes Nächstes Video HP Designjet 5500ps Check Printhead Cleaner Path Error - Dauer: 2:36 Zeb Harris 14.385 Aufrufe 2:36 Designjet 5500 Belt Replacement & Calibration - Dauer: 29:55 Bob Wert 16.367 Aufrufe

Downloading the System Maintenance Utility Click here to go to www.Designjet.hp.com. The Service Configuration Print if possible Page 1-37. The cause is not likely to be the Printhead because if it was, the Printhead would be marked as XX21 REPLACE. http://upintheaether.com/hp-designjet/hp-designjet-5500-error.php Corrective Action: Try the following: Make sure that the Ambient temperature is within the allowed range (between 0 and 55 Degrees Centigrade).

When prompted, save the installation application in the Temp file folder on the C: drive. The mask generation algorithm could not generate the print mask. Scroll to 1.6 Backup EEROM and press ENTER. If the error persists, please call HP for technical support to troubleshoot the problem.

Bitte versuche es später erneut. Also check that the flat cable connector is clipped in correctly. Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. System Error: 010092 (Continuable) Problem Description: Mark Encoder position not detected on Drive Roller.

Click here for information on contacting HP Customer Care. Using this procedure you will be able to determine exactly which component failed. If the error re-occurs or the problem persists, turn the printer off and continue with the remaining steps. top System Error 0B000C (non-continuable) Explanation Serial Device ADC test failure.

Open the cover on the back of the printer to access the ink cartridge assembly (right side of the printer, looking from the back). Recommended action HP recommends printing via the network card because the transmission time via the parallel port is very slow, which may be causing the error. System Error: 0B000C Problem Description: Serial Device ADC test failure. Turn the printer off, wait 15 seconds and turn the printer on.

Corrective Action: Refer to System Error Code 0A0000. Anmelden 2 Wird geladen... Recommended action Press the ENTER key to continue operating.