Home > Hp Designjet > Hp 5000ps Error Codes

Hp 5000ps Error Codes

Contents

If the problem persists, click on Support at the top of the page for additional HP support and contact options. Install normal printheads. Printhead recovery procedure The printer regularly performs a series of controls on the health of the printheads. Only try one recommended action at a time and check if the Error Code has disappeared. have a peek here

If the error continues, call HP for technical support to troubleshoot the problem. If there is, replace that Printhead. Turn the Printer OFF and disconnect the Aerosol Fan from the Main PCA. Ensure that the ink cartridge is the correct orientation, with the color-coded label at the top.

Hp Designjet 5500 Printhead Reseat Error

The type of computer connected to the printer. The Service Station motor has shutdown because of blockage. If the file is PostScript, check to see if it is binary. Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on.

After 10-15 seconds, turn the main power switch on. If there are third-party software drivers and RIPs installed, refer to their user documentation. Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. Hp 5500 Printhead Problems Power ON the Printer and check if the Error Code has disappeared.

Quality, Productivity, or Max. Using a lint-free cloth lightly dampened with water, clean the Mark encoder located on the drive roller (small white rectangle attached to the left-side of the large black drive roller). You can continue using the printhead unless the (XX21) Replace message is displayed (the affect on print quality depends on the print mode). 2. this content If the problem persists, contact HP.

The following pages contain a list of System Error Codes and their respective descriptions and recommended corrective actions. Hp Designjet 1050c Error Codes Click here for information on contacting HP Customer Care. Tighten the thumbscrews. It appears you have air in the tubes that feed the ink to the printheads.

Hp Designjet 5500 Error Codes

Turn on the printer, following initialization attempt to verify printer functionality. System Error: 0B0009 Problem Description: Unable to detect Aerosol Fan (in the Right Cover). Hp Designjet 5500 Printhead Reseat Error top System error 11:11 Explanation The trailing cable is poorly connected. Hp Designjet 5500 Service Manual how important is the Set-heads?

Recommended action Turn the printer off and allow a few minutes for printer to cool. navigate here Select Replace Printheads and press ENTER. The chance of this error appearing is less than 0.5% and there is nothing wrong with the printer. To test if this is a problem, remove the printheads and the power on. Hp Designjet 5500 Printhead Error Codes

If the error returns only when the printer is plugged into the network, the issue is most likely a network issue.Check the network settings (IP address, etc.) on the printer, workstation, Replace the Main PCA Page 8-79. Check inside both end covers to verify no paper is lodged in these areas as well. Check This Out Press the TOP key (to return to the main menu).

Turn the printer on. Hp Designjet 5000 Service Manual Click here for information on contacting HP Customer Care. Recommended action Turn the printer off and allow five minutes for printer to cool.

If the error continues, call HP for technical support to troubleshoot the problem.

Have you also oiled the back rail that the spring loaded clip of the carriage assembly rides on. Recommended action Turn the printer off (using the power switch at the back of the printer). Click here for instructions on upgrading the printer's firmware . Hp Designjet 5100 Error Codes Recommended action Follow the instructions below to help solve the issue: Turn the printer off and allow a few minutes for printer to cool.

Open the printer's window. The percentage of ink remaining. Figure 5: Ink Cartridge information displayed. http://upintheaether.com/hp-designjet/hp-designjet-100-error-codes.php NOTE If the YYYY digits in the second set of 8 characters are zero [0000ZZZZ], this indicates a LAN Card System Error.

Click here for detailed instructions on network card removal . last two digits). Clean the Mark encoder. Upgrade process If the System Maintenance Utility is unable to successfully upgrade firmware to a printer, send the files via DOS by connecting the printer to a PC through the parallel

top When should you replace the HP ink supplies? Recommended action HP recommends printing via the network card because the transmission time via the parallel port is very slow, which may be causing the error. Click here for information on contacting HP Customer Care. If the problem persists, click on Support at the top of the page for additional HP support and contact options.

With the power off open the cleaner door on the right side and pull the cleaner tray out.