Home > Hp Designjet > Hp 5000 Designjet Error Codes

Hp 5000 Designjet Error Codes

Contents

There is nothing wrong with the printer. If all six printhead cleaners present the same error message, check the following: All printhead cleaners installed are not the wrong type i.e. If the error re-occurs or the problem persists, turn the printer off and continue with the remaining steps. If the error continues, call HP for technical support to troubleshoot the problem. Check This Out

If internal printer functionality is verified and the problem persistss, the issue is being caused by a communication failure between the PC and the printer. top System Error 0B0009 (non-continuable) Explanation Unable to detect the Aerosol fan (in the right cover). Click here for instructions on upgrading the printer's firmware . top System Error 06040C Explanation The Line Sensor is not correctly connected. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpp03771

Hp Designjet 5500 Printhead Reseat Error

If the problem persists, click on Support at the top of the page for additional HP support and contact options. Plug the power cable in, turn the printer on and attempt to verify functionality. top System Error 0B000C (non-continuable) Explanation Serial Device ADC test failure. Click here for information on contacting HP Customer Care.

Recommended action Turn the printer off (using the power switch at the back of the printer). top System Error 0B0005 (non-continuable) Explanation Air Pressurization System (APS) failure. Recommended action Turn the printer off and allow a few minutes for printer to cool. Hp Designjet 5000 Service Manual XX02 Reseat There is a problem with continuity problem between the ink cartridge and ink supply station. 1.

The files can be found in the default directory located in C:\Program Files\Hewlett-Packard\HP Designjet System Maintenance. Hp Designjet 5500 Service Manual Scroll to Replace ink cartridges and press ENTER. Figure 2: Pressing the TOP key to go to the main menu Press the UP or DOWN ARROW key to select the cartridges icon, and view status bars indicating ink levels If the error continues, call HP for technical support to troubleshoot the problem.

If the problem persists, click on Support at the top of the page for additional HP support and contact options. Hp Designjet 5500 Air In Tubes Depending on the product's warranty, a fee might be charged. Status Numbers Error Description Procedure XX02 Reseat XX06 Reseat XX08 Reseat Continuity problem between the printhead and the Carriage Assembly. If the problem persists, click on Support at the top of the page for additional HP support and contact options.

Hp Designjet 5500 Service Manual

On the printer's front panel menu, select the Ink menu (Ink Droplet Icon) and press Enter. NOTE: Remove and replace any low or empty cartridges. Hp Designjet 5500 Printhead Reseat Error Figure 8: Selecting Printhead info. Hp Designjet 1050c Error Codes Turn the printer on, and attempt to verify functionality.

Clean the Mark encoder. his comment is here Open the carriage cover and remove all printheads. top System error 81:01 Explanation Paper-axis shutdown. If the problem persists, click on Support at the top of the page for additional HP support and contact options. Hp 5500 Printhead Problems

Send an internal print to the printer to verify internal printer functionality: Load media into the printer (if not already loaded). Attempt to manually recover the printheads: Scroll to the Printhead menu icon (icon on the lower right of the front panel display) and press Enter. Click here for information on contacting HP Customer Care. this contact form top System error 41:10 Explanation A problem has been detected with the Paper-Axis motor.

Remove and re-install all six ink cartridges and press ENTER to continue. Hp Designjet 5100 Error Codes Re-boot the Printer and make sure that the Window is never opened during the cutting operation. Remove the protective cap from the printhead before installing it.

The following table describes the messages and status codes for HP ink supplies, and the recommended actions.

If the error message persistss, check for a new release of the driver. The possible causes are fibers or paper in the Drop Detect sensor, or that the Scan-Axis reference is incorrect. If the error re-appears, upgrade the printer's firmware (if upgrade is available). Hp Designjet 5500 Manual Pdf Ensure that all the ink consumables are HP No. 81 XX13 Replace XX14 Replace XX15 Replace Printhead smart chip failure.

NOTE: A manila folder can be used to aid in removing jammed paper. Wird verarbeitet... Click here for information on contacting HP Customer Care. navigate here Status Numbers Error Description Procedure XX03 Replace The ink cartridge has a leak, which prevents the ink pumping to the printer.

Turn the printer on. Recommended action Turn the printer off and allow a few minutes for printer to cool. If the problem persists, click on Support at the top of the page for additional HP support and contact options. Click here for information on contacting HP Customer Care.

Recommended action Turn the printer off (using the power switch at the back of the printer), wait 15 seconds and turn the printer on. Any special equipment or software (for example, spoolers, networks, switch-boxes, modems, or special software drivers).