Home > Hp Designjet > Hp 1055cm Printhead Error

Hp 1055cm Printhead Error

Contents

by dmzcompute on May 13, 2008 at 6:23pm Add comment Please sign in to comment 0 I removed the printheads and the cleaners, let the plotter boot up then inserted the No help. You can also lay a very light coat of teflon grease over the tape to stop friction. First Time Here? Source

When this happens the motor/belt make a grinding noise of the belt slipping/ skipping over the teeth on the motor. If none come up for your zip code change the miles to 25 or 50.http://h20465.www2.hp.com by dmzcompute on Sep 29, 2008 at 7:29pm Add comment Please sign in to comment 0 Powers up but states close door on right to continue. If the belt is not positioned correctly, then the wrong inside of the belt could be over one of the items causing a path error. http://h30434.www3.hp.com/t5/DesignJet-Large-Format-Printers-and-Digital-Press/hp-1055cm-plus-print-cartridge-problem/td-p/5047960

Hp Designjet 1055cm Printhead Failed

I have checked and reseated all connections..I then replaced the main logic board. You may have a case where the carriage assembly is sitting to low. Melde dich an, um unangemessene Inhalte zu melden. Over 9000h and manufactured in 2005.

So I started doing some experimenting.First, I put the old printhead backin because at least I knew it would seat properly and bring the printer to a ready state. The last thing would be to replace the carriage assembly followed by the main board. by dmzcompute on May 22, 2008 at 7:41pm Add comment Please sign in to comment 0 I just had a look and yes the blue and white cable has been connected Hp Designjet 1050c Printhead Replace It is possible the cable that connects to it is loose or broken.

It keeps asking to be reseated.The old black printhead still works but is streaky so comes up on the screen as "Monitor" or "Replace". Hp 5500 Printhead Problems So, I have now replaced all four printheads - and am beginning to get a second series of "replace printheads."I have tried the 'recover' utility. by dmzcompute on Sep 30, 2013 at 3:33pm Add comment Please sign in to comment 0 I removed the encoder strip off of the back of the printer, and cleaned it by dmzcompute on May 8, 2008 at 2:48pm Add comment Please sign in to comment 0 THANK YOU SO MUCH I DID IT AND THE BELT TIGHT.NOW I NEED TO KNOW

So I started looking at the new printhead, trying to figure out which contacts aren't making contact, making it asked to be reseated all the time. Hp Designjet 5500 Printhead Reseat Error If the carriage moved correctly before the belt change, then I would lean towards you having put one of more connections in the wrong socket. You can check where the tubes enter the carriage assembly, but the best place in to open the left rear door (remove 2 screws) and look at the tubes leading into by dmzcompute on May 25, 2008 at 6:19pm Add comment Please sign in to comment 0 I've read the post from top to bottom.

Hp 5500 Printhead Problems

Generated Sun, 16 Oct 2016 07:33:24 GMT by s_ac5 (squid/3.5.20) http://fixyourownprinter.com/posts/72216 Anmelden 8 Wird geladen... Hp Designjet 1055cm Printhead Failed You could try HP tech support although its very hard to get a hold of an actual real tech anymore. Hp Designjet 1050c Error Codes Sign Up Login Add Question unknown asked Oct 20, 2011 at 11:09am 0 Unknown Printer Designjet 1055CM - Bad Printhead error I have a Designjet 1055CM that keeps giving us a

Du kannst diese Einstellung unten ändern. http://upintheaether.com/hp-designjet/hp-designjet-1055cm-printhead-path-error.php Please try the request again. Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content ‎03-19-2013 06:30 PM Got the new printhead directly from HP, plugged it Very easy to put them in wrong. Hp Designjet 1050c Printhead Error

Please help! by dmzcompute on Oct 1, 2013 at 4:03pm Add comment Please sign in to comment 0 I have already oiled the rails, replaced the belt as well as the motor and You will want to start the plotter in service mode by pressing the color button as your turn on the plotter. have a peek here Now move the carriage all the way to the left.

If you reseat the ph and don't have a new cleaner you must cover that black rectangular block with a piece of paper and tape…make sure the tape is not in Hp Designjet 1055cm Plus Manual I oiled the rails again ao i don't know. In the back of the carriage assembly are two torx 8 or 9 screws which you loosen.

Learn How to Post and More  Community News  Best of the Community Blog  Notebooks Notebook Operating System and Recovery  Notebook Boot and Lockup  Notebook Wireless and Networking  Notebook Audio  Notebook Video,

Melde dich bei YouTube an, damit dein Feedback gezählt wird. If not blown, then remove the trailing cable from both the carriage and the emod and reinsert and just be very careful and check the metal contacts on the ends to First off was the plotter doing the same thing before you changed the belt? Send to Email Address Your Name Your Email Address Cancel Post was not sent - check your email addresses!

Ouch! My printer stopped mid printing and displayed the "Check Printhead Path type 2" error. I THINK I read that running them out of ink can cause them to short out but not certain about that. Check This Out If you get 2 lines of ink on the towel then the head has ink and your issue could be electrical in nature.

by Speedin360 on Oct 1, 2013 at 2:35pm Add comment Please sign in to comment 0 Sounds like you are having a friction or belt issue. by dmzcompute on Nov 15, 2010 at 4:26pm Add comment Please sign in to comment 0 I have a 1055plus which when powered up gives a blank screen and no red Diese Funktion ist zurzeit nicht verfügbar. You can change this preference below.

There are many causes such as and not limited to, obstructions, not cleaning the crud off the motor pully when replacing the belt, worn tube assembly rubbing on the top frame, They are literally brand new. by dmzcompute on Apr 14, 2008 at 4:29pm Add comment Please sign in to comment 0 i just changed the belt on this machine, i replaced the trailling cable, checked the The instructor soldered a fuse over the blown one on the board, did not remove the old one.

Wird geladen... Über YouTube Presse Urheberrecht YouTuber Werbung Entwickler +YouTube Nutzungsbedingungen Datenschutz Richtlinien und Sicherheit Feedback senden Probier mal was Neues aus! Maybe I should start from the start again??????? Pull the PH cleaner tray forward and remove select cleaners. What has happened is the printer will clean the black printhead then due to it being the last printhead to the right of the carriage, it has to pass over the Cyan,

Any help would be Greatly appreciated. What happens when you replace a printhead is once the plotter see the head as new it accepts it and then tells you to replace the cleaner for it and at I have used heavy duty packaging tape which also has worked just fine. I get a "Clear Printhead Path (2) " error when I turn on the printer.