Home > Hp Designjet > Hp 1055cm Check Printhead Path 2 Error

Hp 1055cm Check Printhead Path 2 Error

Contents

Open the printhead cleaner door, located on the right side of the printer. I have read all of the above posts, and a bunch of the manual. The instructor soldered a fuse over the blown one on the board, did not remove the old one. Maybe I should start from the start again??????? Source

Check Printhead Path (1) This warning appears whenever friction on the Scan-Axis is too high: the electrical current needed by the Scan-Axis Motor to move the Carriage is too high, so before burning Unload media and check for obstructions in the carriage path, remove as needed. The door is closed. some one told me replace all printer heads as they are expired (date is old)...so I reaplced all new printer heads still I get same error same error....please help on this

Hp Designjet 1050c Printhead Path Type 2

Sometimes the tube assembly at the top malforms and then rubs against the top and causes the error. Check ebay also. If that does not clear up the problem, you may have a bad trailing cable (carries all the signals to and from the print heads) or a bad carriage. Put it back in and it's up and running having problems feeding the paper but I heard with this printer its always a problem.

After I insert the cleaners the carriage comes across and scans them but then beeps and tells me that I have to insert the printhead cleaners.I have no idea what it's Teacher: An expert who has written 2 tips or uploaded 1 video tip. cheers for your help though. Hp Designjet 1050c Printhead Alignment Error This procedure often solves the issue without requiring service.

Du kannst diese Einstellung unten ändern. In another case on another printer, a stiffer spring did overcome the belt slippage grinding sound when the carriage is to the far left. Fill in your details below or click an icon to log in: Email (required) (Address never made public) Name (required) Website You are commenting using your WordPress.com account. (LogOut/Change) You are DesignJet 1050c plus...

I have checked and reseated all connections..I then replaced the main logic board. Hp Designjet 1055cm Printhead Failed Reply 0 0 fse Top Student Posts: 7 Member Since: ‎12-03-2013 Message 7 of 8 (3,849 Views) Report Inappropriate Content Re: 1055CM "check printhead path type (2)"--replaced motor twice, came back That cable is the sensor/switch cable. The tool is a must if you change the carriage belt to adjust the height afterwards.

Check Printhead Path Type 1

Help this question get an answer by entering the correct category or product below. First the machine is switched off (to avoid damage to the Designjet) before opening up the printhead cover. Hp Designjet 1050c Printhead Path Type 2 Dec 26, 2012 | HP DesignJet 1050c plus InkJet Printer 1 Answer On my HP 1050C Designjet I am getting the error 'Check printhead path Type 2. Hp Designjet 1055cm Check Printhead Path Type(1) If that is the case, then with the power off, open the right front door where the cleaners are located and pull them out.

After research, reading the manual, and visual inspection I noticed the belt was worn and replaced it. this contact form I did use the height adjustment tool. Maybe for some reason it is just too tight in that vicinity.Thanks for any and all input.Paul Reply 0 Reply 0 0 Everyone's Tags: EBCOMMIPG View All (1) pbrooks259 Teacher Posts: If this error continues stop using the printer till the belt is replaced because if this error doesn't go away, which is caused by the main circuit board detecting how much Hp Designjet 1055cm Check Printhead Cleaner Path

When you did not have the printheads installed and it then asks you to open the cleaner door and insert the cleaner after installing the printhead and you do open and Generated Sun, 16 Oct 2016 08:47:36 GMT by s_ac4 (squid/3.5.20) If you remove the top cover you will see the tread marks made by the tube assembly. http://upintheaether.com/hp-designjet/hp-designjet-1055cm-printhead-path-error.php Cleaned and oil the rails inside and still the same result.I searched around the read that it 'May' be the belt that needs replacing so promptly ordered a genuine belt from

by Speedin360 on Oct 2, 2013 at 11:00am Add comment Please sign in to comment 0 Get the service manual. Hp Designjet 1050c Error Codes HINT: Adjusting the carriage height is probably the most important thing you need to do when you change the belt and the clutch will have absolutley nothing to do with the Have never heard of the motor going right on startup.

by Speedin360 on Oct 1, 2013 at 5:07pm Add comment Please sign in to comment 0 Only 2 things left as long as the encoder is fine.

by copyplus on Sep 4, 2014 at 5:26pm Add comment Please sign in to comment 0 Just got this from an auction. Jan 23, 2014 | HP DesignJet 450c InkJet Printer 1 Answer Hp designjet 1050c check printhead path (1) but the carriage barely moves? Do so using the belt to move the carriage and see if you get any bumping or other action when it reaches the area you are having problems. Hp 1055cm Belt Open the printhead cleaner door, located on the right side of the printer.

Now move the carriage assembly out and then using the belt move the carriage assembly back and forth over the complete width and see if you can spot and tight spots Scholar: An expert who has written 20 answers of more than 400 characters. Everything I said previous means nothing as this missing part is your issue. Check This Out My mistake.It's very interesting that I've been to the site twice, and both times the supposed "fix" each time lasted 1-2 weeks.

What everyone needs to do is to turn the plotter off and then use the belt to move the carriage all the way to the left and then all the way The best test you can do is with the power off open the cleaner door on the right and pull out the cleaners. Also when the carriage moves all the way to the left and stops do you get any sort of error message on the display or is it still in the initializing After I remove the tube ink station and then the cover I put the tube ink station back in the open area just to get it out of the way.

Yeah make sure the belt is new and in good condition. by dmzcompute on Apr 22, 2008 at 2:31pm Add comment Please sign in to comment Does anyone know the correct fuse to use in the F7 slot? When the "READY" message is displayed on the front-panel, scroll to the Printer Setup Options icon and press ENTER. by dmzcompute on May 13, 2008 at 7:23pm Add comment Please sign in to comment 0 Ok I removed all the printheads and left the cleaners in there, as the plotter

Not saying that you are not doing things told to do, but most times this is what happens when a person has a problem as you have. Hinzufügen Playlists werden geladen... Use a manila folder to remove jammed media from the media path (take care not to damage the media sensor on the right side of the printer). I cleaned it with a moist cloth when I first got the errors, wouldn't hurt to replace it I guess.As for the spring, I hated putting it back together without one

Melde dich bei YouTube an, damit dein Feedback gezählt wird. I tried to clean, oil and turned on and off but the problem did not go. I lubed all I could think to lube--the carriage rails and the ink tubes assembly channel. Use the belt to move it and see if moves smoothly or has a bumping action.

If printer is 60-inch model and no full-width media is available cut 36-inch media at a length of 60 inches to create a 60 x 36-inch sheet of media. by Freak on May 22, 2008 at 10:30pm Add comment Please sign in to comment 0 I am not talking about the one that connects to the main board in the On that model the test point is very hard to get to and in reality when you do get a ready it is like one that starts high and works its