Home > Hp Designjet > Hp 1055 Error Codes

Hp 1055 Error Codes

Contents

Color to Color calibration 5-16 7. Remove the EIO Card (if installed) and make sure that the Hard Disk Drive is installed correctly by pushing it firmly inwards and checking that the two installation screws are completely HP DesignJets 1050C and 1055CM Printers Service Manual Print Quality C6074306... Also you will want to clean the surface of the drop detector and make sure there is no paper in the hole of the drop detector as that can cause issue, Source

Search the Community Entire ForumThis CategoryThis BoardUsers turn on suggested results Auto-suggest helps you quickly narrow down your search results by suggesting If the card is a 610n or 615n look for baking instructions elsewere on this board. If the belt is not positioned correctly, then the wrong inside of the belt could be over one of the items causing a path error. I assume you are putting them in the right slots as each color has it own slot. http://www.lcrsales.com/knowledge-center/plotter-faqs/designjet-1050-designjet-1055-error-codes/

Hp Designjet 1050c Service Manual

Page 124 Accuracy Calibration are NOT ALL zero. Hide thumbs 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Before I read I considered myself somewhat handy.

The cable is blue and white and interconnects inside the cover. To check the cable you remove the right side cover by removing the display cable and the fan cable. Z7_3054ICK0KGTE30AQO5O3KA3072 hp-country-locator-portlet Actions ${title} Loading... Hp Designjet 1055cm Plus Parts NOTE If the Printer DOES NOT function correctly with the Hard Disk Drive and the Network Card removed, then you must replace the Electronics Module.

The front panel will display: Printing. Hp Designjet 1050c Owners Manual Do so using the belt to move the carriage and see if you get any bumping or other action when it reaches the area you are having problems. However, the printer can still produce good quality line prints. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.

Only replace one component at a time and check if the error has gone before replacing another component. Hp Designjet 1050c Plus Parts Re-order part number of the ink cartridge. Roller Mark Position 5-13 5. Also make sure the belt was put on right as there are 2 different grooves on the belt inside one which moves over the pulley and one which moves over the

Hp Designjet 1050c Owners Manual

by qman29 on Sep 30, 2011 at 1:07pm Add comment Please sign in to comment 0 You need to read all the post above. http://h30434.www3.hp.com/t5/DesignJet-Large-Format-Printers-and-Digital-Press/hp-1055-error-code-09c000/td-p/5220432 Speed offset STD Speed offset 4-18 Running Scan Axis Test... (takes 2mn...) Scan-Axis Forward Normal Maximum 1800 2400 HP DesignJets 1050C and 1055CM Printers Service Manual Scan-Axis Backwards Normal Maximum -165 Hp Designjet 1050c Service Manual Test Prints ... Hp Designjet 1055cm Network Configuration Remove 2 screws (Item 1) that attach the Right Hand Trim (Item 2) to the Printer. 4.

Solving Image Quality Problems Whenever an Image Quality problem appears, it is advisable to print the Image Quality Print to help diagnose the problem. this contact form Before I start doing all the checks mentioned above, I have noticed the light blue dashes that the print head scans across after each print have practilly worn away on one Figure 2: Front Panel HP DesignJets 1050C and 1055CM Printers Service Manual C607436... Electrostatic Discharge Refer to the beginning of Chapter 8 of this manual, for precautions you should take to prevent damage to the Printer circuits from electrostatic discharge. Hp Designjet 1055cm Plus Troubleshooting

Using this procedure you will be able to determine exactly which component failed. 010050 XXXXXXXX (Non-Continuable) PostScript Processing Error. HP DesignJets 1050C and 1055CM Printers Service Manual Service Tests and Utilities Back Make Selection Press Enter... Find support and troubleshooting info including software, drivers, and manuals for your Troubleshooting Software and Drivers 3 How to Product Information User Guides Video Tutorials More Support Options Solution have a peek here What everyone needs to do is to turn the plotter off and then use the belt to move the carriage all the way to the left and then all the way

The printer does not recognize the printhead or printhead cleaner Wrong Model that you have inserted into the printer. Hp Designjet 1055cm Parts Page 182: Left Hand Cover And Window Ink Tubes System (Includes Setup Printheads, Ink Collector, Carrier Clip, Nye Oil and ISS Housing Foam) Nameplate (HP DesignJet 1050C) Nameplate (HP DesignJet 1055CM) Scan Axis 4-17 6.

Page 57: Hp No.80 Ink Supplies Troubleshooting Printheads and Printhead Cleaners 3-2 Identifying the Components 3-3 General Information About HP No.80 Supplies 3-4 Some General Precautions When Handling HP No.80 Supplies

Accuracy Calibration 5-6 2. This process can take several minutes depending on the number of warranties being checked. by dmzcompute on May 10, 2008 at 3:59pm Add comment Please sign in to comment 0 Mine staying on the left and the noise comming from the belt not from the Hp Designjet 1050c Parts This type of problem affects mostly Normal and Draft modes.

by dmzcompute on May 3, 2007 at 5:12pm Add comment Please sign in to comment 0 Hello, i am original poster to this thread. Page 49 Using this procedure you will be able to determine exactly which component failed. 0A0060 (Non-Continuable) System Error: The Printer has detected a leak in the Tubes System after the Cut Sheet rice paper loading failure Thin rice paper is sucked into the Center Platen grooves and Linear Blade Ridge. http://upintheaether.com/hp-designjet/hp-designjet-100-error-codes.php When removing the Service Station, make sure that you release...

Showing results for  Search instead for  Do you mean  or Post new question Question Reply Topic Options Subscribe Mark Topic as New Mark Topic as Read Float this Topic to the Note: This tool applies to Microsoft Windows PC's only. Has anyone had the "Check Printhead Path" error before on an HP plotter. Corrective Action: Try the following: WARNING ■ Remove ALL the Printheads and clean the flex contacts on the Printheads and in the Carriage Assembly (Refer to Chapter 2). ■ Perform the

Without this information, HP Support Personnel cannot help you. Check firmware in Utilities / Statistics / Code rev. ■ The complete error number (See Note below). ■ The Service Configuration Print => Page 1-19. ■ The Current configuration sheet. ■ Check warranty status Please wait while we process your request. Maybe I should start from the start again???????

If the Error Code reappears, then the EIO Card could be faulty. If the Error Code continues, replace the Electronics Module Page 8-25.