Home > Hp Designjet > Hp 1050c System Error

Hp 1050c System Error

Contents

Paper Axis 4-20 7. Once in Utilities menu, press the Up Arrow key and the Enter key simultaneously. Using the Arrow keys, scroll to Menu Mode =. Try the following: ■ Wait at least 60 minutes to achieve the high gloss appearance. 34" Rice Paper not supported Roll length is 34" (Non-standard) and the pinch wheels can't control Source

HP DesignJets 1050C and 1055CM Printers Service Manual 1-9 Troubleshooting Printhead Crashes/Smears on High Density Prints Using Coated Media High density prints can cause cockle mainly on HP Coated Media. Power the Printer OFF and ON again to see if the System Error disappears. Using this procedure you will be able to determine exactly which component failed. The right-hand edge must be parallel to the white line on the paper entry roller.

Hp Designjet 1050c Service Manual

I Enter Printer setup options IPen settings ... Follow the steps listed below to determine the actual cause of the failure and to replace the appropriate parts. Also inspect ALL Ink Cartridges for any signs of leaking (the bottom valve of the Ink Cartridge will contain ink). Check all the tubes of the APS and make sure they are NOT pinched or damaged.

Using this procedure you will be able to determine exactly which component failed. 010050 XXXXXXXX (Non-Continuable) PostScript Processing Error. Using this procedure you will be able to determine exactly which component failed. This is because the part of the print exposed to the air is always lighter than the covered one. Hp Designjet 1050c Error Codes Figure 3: Six screws to remove.

Corrective Action: Try the following: WARNING ■ Perform the Service Station Calibration => Page 5-11. ■ Replace the Drop Detector Assembly => Page 8-10. ■ If the Error Code continues, replace Without this information, HP Support Personnel cannot help you. Turn the printer on and allow initialization to complete. Replace the complete APS => Page 8-20.

Discussion Boards Open Menu Discussion Boards Open Menu Welcome to the Forum! Hp Designjet 1050c Owners Manual System Error: Problem Description: Corrective Action: Try the following 0A0010 Problem in Pressurizing the Air System. Printer Model Type 4-35 5. Following replacement, turn the printer on and perform a Calibrations Backup and a Pen Alignment Calibration as listed below (Perform a Carriage Height Calibration per instructions shipped with Carriage Height tool).

Hp Designjet 1055cm Error Codes

NOTE The media is causing the problem and NOT the Printer. If you receive a prompt to print a calibration page, do so. Hp Designjet 1050c Service Manual Select Accept to continue the Calibrations Backup. Hp Designjet 1055cm Plus System Error Codes First Edition, March 1999 The information contained in this document is subject to change without notice.

Use an Ohmmeter to check F7. this contact form The Trailing Cable has been incorrectly connected OR the fuse in the Electronics Module has been burned. This effect make it almost impossible to load the rice paper correctly because the Vacuum is too high. Search the Community Entire ForumThis CategoryThis BoardUsers turn on suggested results Auto-suggest helps you quickly narrow down your search results by suggesting Hp Designjet 1055cm Plus Manual

WARNING TAKE CARE WHEN CONNECTING THE TRAILING CABLE TO THE ELECTRONICS MODULE OR CARRIAGE. Scroll to Accept and press Enter. If the user does not replace the Ink Cartridge immediately, when the printer starts to print again, a band will appear in the position where the printing restarted. http://upintheaether.com/hp-designjet/hp-designjet-1050c-plus-system-error.php If the Error Code reappears after sending the print again, then report the error to the HP response Center or the nearest HP Support Office, stating the following information. ■ Model

Select Full (if needed) and press the BACK key to return to the main menu. Hp Designjet 1055cm Network Configuration Clear the media path. NOTE Make sure that you select "Tubes Replaced" when performing the Calibrations Backup.

When all required calibrations are complete, return to the main Status display using the Back key.

HP DesignJets 1050C and 1055CM Printers Service Manual 2-9 System Error Codes System Error: Problem Description: 060309 Problem with setting the Voltage of the Printheads. Vacuum suction much lower at high altitudes At altitudes above 3,000 meters, the vacuum force holding down the media will be lower, therefore the media will not be held in place If no service has been performed and printer was working normally before the error occurred, continue with the section Steps for printer working normally prior to error listed below. Hp Designjet 1055cm Plus Troubleshooting The firmware is identical for the 1050C Plus and 1055CM Plus Note: The aerosol fan is not used in the Designjet 1050C Plus or 1055CM Plus.

Click "Add" to insert your video. When reporting the System Error Code, make sure that you supply the full Error Code (including the last 8 numbers where applicable) and the firmware version. Bin marks on prints done on HP High Gloss media Prints done on HP High Gloss media are sensitive to scratches when they fall into the media bin. http://upintheaether.com/hp-designjet/hp-designjet-1050c-system-error.php Faulty APS Sensor.

Return to TWI Documents Library Index Page HP Designjet 1000 Series Printers - TWI: System Error 0B0007 In this document: Tools required Parts required (part numbers are subject to change) Troubleshooting Make sure to properly connect the trailing cable or replace a shorted trailing cable before installing the new fuse. For information on solving Image Quality problems see Chapter 6 - Print Quality. The printer will begin the pen alignment and display the time remaining to complete the calibration.

NOTE When reporting the System Error Code, make sure that you supply the full Error Code (including the last 8 numbers where applicable) and the firmware version. Corrective Action: Try the following: WARNING ■ Remove ALL the Printheads and clean the flex contacts on the Printheads and in the Carriage Assembly (Refer to Chapter 2). ■ Perform the Clean the Overdrive using the Overdrive Cleaning Service Utility => Page 4-37. NOTE If the test on that component/assembly passes, you should NOT replace it.

Following replacement of the Electronics module, turn the printer on and perform a Calibrations Backup and a Pen Alignment Calibration as listed below. Repeat steps 1-8, if problems persist continue with the remaining steps. contact your HP rep. Corrective Action: Refer to System Error Code 070100.

This information is useful for troubleshooting Printhead problems and even knowing if the Printheads have been used with Non-HP Cartridges. ■ Cartridge Info - In this area you can find all If functionality is verified, no additional parts should be replaced. If the problem remains after replacing the failing Printhead then check if the customer is using a 3rd Party RIP. When the calibration is complete press Enter to continue.

HP DesignJets 1050C and 1055CM Printers Service Manual Previous page Next page 1...484950515253545556 Also See for HP DesignJet 1050C HP DesignJet 1050C User Manual 286 pages HP Designjet 1050c Reference Once the Error Code has been solved, print an Internal Demo Print to make sure that the Hard Disk Drive is functioning correctly. When plotter's power is on, press Setup and Cancel keys simultaneously. Only replace one component at a time and check if the error has gone before replacing another component.

Line Sensor 5-9 3. To find the environmental conditions, print the Service Configuration Print (Printer Setup Menu I Utilities I Test prints I Service config) 1-10 HP DesignJets 1050C and 1055CM Printers Service Manual Troubleshooting Power ON the Printer and check if the Error Code disappears. Troubleshootingpage 13................................................................................................................................................................