Home > Hp Designjet > Hp 1050c Printhead Error

Hp 1050c Printhead Error

Contents

If that is the case, then with the power off, open the right front door where the cleaners are located and pull them out. Hope some of this helps. Any suggestions? Sale: Designjet printers - Consumables - inks - Media View all posts by www.1stcall4service.com → This entry was posted in Designjet Service, HP Designjet 1050c, Old Family HP Designjet Series. http://upintheaether.com/hp-designjet/hp-1050c-reseat-printhead-error.php

I can't take chances. Reply 0 0 davidzuts Regents Professor Posts: 4,701 Member Since: ‎01-17-2009 Message 8 of 9 (2,085 Views) Report Inappropriate Content Re: HP 1050C Yellow Printhead Error Options Mark as New Bookmark why can't i just order this valve assembly and replace the defective one? Have never heard of the motor going right on startup.

Hp Designjet 1055cm Printhead Failed

by Freak on May 25, 2008 at 5:22pm Add comment Please sign in to comment 0 All I know is when a new cleaner is installed the carriage assembly moves over Have already replaced all printheads as well as carriage belt due to wear but errors still occur. I spent a lot of time explaining what I have seen and done over the years and if you bother to read what I have posted you might be able to

Be very careful if you disconnect the trailing cable from either the carriage or the emod. by dmzcompute on May 8, 2008 at 2:48pm Add comment Please sign in to comment 0 THANK YOU SO MUCH I DID IT AND THE BELT TIGHT.NOW I NEED TO KNOW When I looked it the drive shaft had a black bulging built-up covering about 3 teeth.-rbc by unknown on Dec 16, 2009 at 12:11pm Add comment Please sign in to comment Hp 1055cm Printhead Les Reply Jeffrey Utter says: April 26, 2011 at 11:09 pm Les Please send me your contact information about a possible service call.

Search for: Categories 3D Consumable 3D printer Accessories 3D Printer Consumables 3D Printers Canon Printers Designjet Media (rolls Paper) Designjet Service Finishing Hp 500 Designjet HP 510 Designjet HP 800 Designjet Hp Designjet 1050c Printhead Reseat 6 As part of our ongoing commitment we have now created a new website to provide our existing customers and new prospects a highly informative website enabling you to get the best I bought a used 1050C and knew that the black printhead needed to be replaced per the front panel. Have the cleaners in the tray and remove the printheads and start the plotter and when it ask for the printheads install them and when it asks for the cleaners just

by dmzcompute on May 1, 2007 at 8:09pm Add comment Please sign in to comment 0 I use an HP 1050C and I am having a similar problem. Hp Designjet 5500 Printhead Reseat Error Reply Rick says: January 6, 2011 at 11:53 pm One more note…the reason the Magenta cleaner and other colors…more so the Magenta builds up in the ph cleaner spittoon sponge is I get a "Clear Printhead Path (2) " error when I turn on the printer. If this happens don't replace the black printhead just go through the motions of replacing the printhead by pulling out printhead then back in, when you get to the stage of "ASKING

Hp Designjet 1050c Printhead Reseat 6

the black was at a reseat status, we cleaned the connectors with alcohol on both ends but it just went to faulty status. If the sensor/switch is broken, then the cover needs to be replaced. Hp Designjet 1055cm Printhead Failed What has happened is the printer will clean the black printhead then due to it being the last printhead to the right of the carriage, it has to pass over the Cyan, Hp 5500 Printhead Problems In other words tell us what happens on the screen and the same time what happens to the carriage.

If you look at the belt the inside changes at one point from grooves which run on the pully to lines up and down which run on the motor. http://upintheaether.com/hp-designjet/hp-1050c-error-codes.php Bob Wert 17,450 views 25:40 Designjet 1055cm Ink Tube Assembly Removal - Duration: 1:56. Just take a lint free cloth and remove the black printhead and just blot it on the cloth. To make things easier for everyone concerned if you still have an issue only post what happens when you move the carriage assembly by hand and that is after you have Hp Designjet 1050c Error Codes

Thank you for all of the information you have provided; much of it over and over again. I remember one I had a few years back that the black acted the same and on the 3rd printhead it worked just fine. You probably would just have to buy a few extras just in case. this contact form by dmzcompute on May 9, 2008 at 3:54pm Add comment Please sign in to comment 0 Im sorry im confusing you but I'll try again to explain myself better.When I turning

We replaced the carriage belt due to being worn and which would have failed within 6 months of visit. Hp Designjet 1050c Printhead Replace Put it back in and it's up and running having problems feeding the paper but I heard with this printer its always a problem. In order to do this you need to use the tool I describe in my answer to Freak above.

Results 1 to 7 of 7 Thread: HP Designjet 1050c printhead faulty Thread Tools Show Printable Version Email this Page… Subscribe to this Thread… Display Linear Mode Switch to Hybrid Mode

Sign in to report inappropriate content. we also seen that the carriage belt is torn. At one point it indicated the Yellow was OK and the CM and K indicated a Failed 15 error. Hp Designjet 1050c Black Printhead Close Yeah, keep it Undo Close This video is unavailable.

Is it smooth the complete width of the plotter, is there any bumping action or tightness. Now using the belt move the carriage assembly back a forth and look for smooth movement. That plotter is around 10 to 12 years old. navigate here Result was no change...blank screen and no power led.

by dmzcompute on Apr 22, 2008 at 2:31pm Add comment Please sign in to comment Does anyone know the correct fuse to use in the F7 slot?