Home > Hp Designjet > Hp 1050c Plus System Error

Hp 1050c Plus System Error

Contents

Got it, continue to print 2012-2016 ManualsLib.com About Us About ManualsLib Privacy Policy F.A.Q. Sign-in Register Site help Skip to ContentSkip to FooterLaptops & tablets Business Premium Gaming Standard laptops Workstations Convertibles & detachables Tablets 3-in-1 Desktops Business Immersive Gaming Towers Workstations All-in-ones 3-in-1 Printers Using the Arrow keys, scroll to Menu Mode =. If no service has been performed and printer was working normally before the error occurred, continue with the section Steps for printer working normally prior to error listed below. have a peek here

The printer should now move the carriage/printheads to an accessible position. Return to TWI Documents Library Index Page HP Designjet 1000 Series Printers - TWI: System Error 0B0006 In this document: Parts required (part numbers are subject to change) Troubleshooting steps Calibrations Following the calibration, turn the printer off then on and verify functionality. Following the calibration, turn the printer off, then on and verify functionality. http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpp03899

Hp Designjet 1050c Service Manual

Check that the cable from the Ink Supply Station (ISS) PCA to the Ink Supply Station is correctly connected. Reply 0 0 dirkster Honor Student Posts: 4 Member Since: ‎07-14-2014 Message 3 of 6 (1,042 Views) Report Inappropriate Content Re: HP 1050c with Spinjet unit - System error 04C300 004D0000 Remove Six T-20 screws that secure the right side cover to the Multi-Roll feeder from the front (see Figure 6). Click "Add" to insert your video.

NOTE: If Removal and Installation instructions are needed for reference during any repairs performed, refer to the 1000 Series Service Manual available on the Computer Care Web site for review Figure 1: Screws to remove. Problem Description: Try the following: Corrective Action: n n 0B0001 System Error: Bad Humidity read. Hp Designjet 1055cm Plus Manual Follow the steps listed below to accurately troubleshoot the issue, and replace the appropriate parts.

Was the information on this page helpful? Hp Designjet 1055cm Plus System Error Codes Dec 03, 2010 | HP Design Jet 4020 InkJet Plotter Printer 1 Answer My Hewlett Packer Design Jet 650C the display quit Go to http//www.hp.com Apr 13, 2010 | HP Printers prev next 3 Points Related Questions: 1 Answer Resetter EEPORM in the SERVICE MENU'. Access the Electronics module (remove the small cover on left side) and visually inspect the fuse located on the upper left corner of the Electronics module (newer Electronics modules).

If no fuse, continue with Step 6. System Error 060308 00000008 If fuse is burned, replace the Carriage, Trailing cable and fuse. NOTE: In rare cases the ISS PCA, Y-motor and possibly the X-motor have been known to cause this failure. Anytime I encountered this error the main board needed replacing.

Hp Designjet 1055cm Plus System Error Codes

Make sure to properly connect the trailing cable or replace a shorted trailing cable before installing the new fuse. see here HP DesignJets 1050C and 1055CM Printers Service Manual Previous page Next page 1...484950515253545556 Also See for HP DesignJet 1050C HP DesignJet 1050C User Manual 286 pages HP Designjet 1050c Reference Hp Designjet 1050c Service Manual Expert 196 Answers Re: What is system error 0B0006 on Hp design Jet plotter?... Hp Designjet 1050c Error Codes Check that the Air Pressurization System Sensor Cable is correctly connected and is NOT damaged.

Reply 0 0 « Message Listing « Previous Topic Next Topic » Related Documents HP Designjet Printers Supported in OS X v10.11 El Capitan, OS X v10.10 Yosemite, OS X v10.9 navigate here When plotter's power is on, press Setup and Cancel keys simultaneously. Turn on the printer. Following replacement, turn the printer on and perform a Calibrations Backup and a Pen Alignment Calibration as listed below (Perform a Carriage Height Calibration per instructions shipped with Carriage Height tool). Hp Designjet 1055cm Error Codes

Parts required (part numbers are subject to change) Part Description Models - C6074A, C6075A Models - C6074B, C6075B Trailing Cable (Required) C6074-60418 C6074-60418 Carriage Assembly (Required) C6074-60388 C6074-60388 Electronics Module If the error re-appears or problems persist, turn the printer off and remove the power cable from the back of the printer. Remove six T-20 screws that secure the right side cover to the multi-roll feeder from the front. Figure 6:Screws securing front right-side panel Remove nine T-20 screws that secure http://upintheaether.com/hp-designjet/hp-designjet-1050c-plus-system-error.php Problem Description: Try the following: Corrective Action: n n n n n WARNING Only replace one component at a time and check if the error has gone before replacing another component.

System Error 21:10 0X3010002 Task Temech file sequence.c line 758 Without turning off the product, disconnect the USB cable from the rear of the product. Hp Designjet 1050c Error 060308 00000008 According to your descriptions, there is System Error Code shown on your control panel. Continuable and Non-Continuable Error Codes Some of the Error Codes are continuable, which means you can press Enter on the front-panel and continue working with the Printer.

Select Full (if needed) and press the Back key to return to the main menu.

Turn the printer on. CAUTION: Be careful not to break the door when removing it. Parts required (part numbers are subject to change) Part description Models - C6074A, C6075A Models - C6074B, C6075B Electronics Module (Required) C6072-69146 C6074-60283 Main Logic PCA (Required) N/A C6074-60283 Electronics Hp Designjet 1050c Driver Select Full (if needed) and press the Back key to return to the main menu.

when the lights on for Ready+Cartridges+Data (DKL), it may have 9 possible causes referred by Service Manual page 2-7. Remove the right door and front top cover from the multi-roll feeder (follow steps 1 through 5 of the previous section and remove the right door instead of the left). Following replacement, turn the printer on and perform a Calibrations Backup, and a Pen Alignment Calibration as listed below (Perform a Carriage Height Calibration per instructions shipped with Carriage Height tool). http://upintheaether.com/hp-designjet/hp-designjet-1050c-system-error.php Use the information below to determine the cause of the failure and perform the necessary troubleshooting steps to resolve.

When printing from a Rampage prepress system, I have recently started getting the system error 04C300 004D0000. If the fuse is NOT blown (value less than 1 ohm), replace the Carriage and Trailing cable (refer to pgs. 8-44, and 8-39 of the Service Manual). thanks and regards kindly rate this solution Posted on Feb 12, 2011 Helpful 1 Not Helpful Comment Flag You can't post conmments that contain an email address. × Comment Anonymously Video If fan noise is audible continue with step 17.

Troubleshooting steps Turn the printer on. Figure 10: Removing the right side cover. Reply 0 0 dirkster Honor Student Posts: 4 Member Since: ‎07-14-2014 Message 6 of 6 (971 Views) Report Inappropriate Content Re: HP 1050c with Spinjet unit - System error 04C300 004D0000 Turn the printer on.

Repeat steps 1-8, if problems persist continue with the remaining steps. Remove six T-20 screws that secure the left Side cover to the Multi-Roll feeder from the front (see Figure 3). Scroll to Accept and press Enter. Corrective Action: Turn the Printer OFF and disconnect the trailing cable.

Also check fuses F7 and F8 on the Electronics module before powering the printer On with new E-mod (fuses F7 and F8 should measure about the same resistance when compared to Contact HP? Thank you for using Fixya.com document.tlSearch.tx.value=unescape("") Feb 09, 2010 | HP DesignJet 5000ps InkJet Printer 1 Answer Hp design jet 4000ps plotter printhead required urjently pl. At the Ready prompt, scroll to the Printer Setup menu (icon of printer in the lower-right side of the front panel display) and press Enter.

Reply 0 Re: HP 1050c with Spinjet unit - System error 04C300 004D0000 07-14-2014 07:20 PM Error is a EIO error. Figure 7: Nine screws to remove. System error codes are hexa-decimal based numbers generally caused by internal system errors. The Trailing Cable has been incorrectly connected OR the fuse in the Electronics Module has been burned.

Pings ok. Remove all four printheads from the carriage. Loosen the two screws that secure the left door to the Multi-Roll feeder (see Figure 1). Open the rear access panel and reseat the Firmware and Memory.