Home > Hp Designjet > Hp 1050c Error Codes

Hp 1050c Error Codes


Reconnect the power cord and power On the Printer and check if the Error Code has been resolved. ■ If the Error Code continues, replace the Electronics Module => Page 8-25. Ink Pressure System 4-14 5. Reseat the printhead into the correct position. Do NOT use any other type of media apart from HP Coated or HP High Gloss Photo Paper. have a peek here

Page 140: Carriage Height Calibration Service Calibrations Carriage Height Calibration The purpose of this Service Calibration is to adjust the distance between the Carriage Assembly and the Center Platen. Air Pressurization System (APS). WARNING IF POSSIBLE ALWAYS PERFORM THIS TEST BEFORE REPLACING THE EIO CARD. Page 33 Troubleshooting Sample of the Service Configuration Print 1-21 HP DesignJets 1050C and 1055CM Printers Service Manual... http://www.lcrsales.com/knowledge-center/plotter-faqs/designjet-1050-designjet-1055-error-codes/

Hp Designjet 1050c Service Manual

Page 215: Right Hand Trim And Window Switch 3. Calibrations. Make sure you select "Tubes Replaced" when performing the Calibrations Backup. Pen Alignment 5-22 Carriage Height Calibration 5-24 HP DesignJets 1050C and 1055CM Printers Service Manual...

Page 25: Lower Image Gloss Directly After Printing On Hp High Gloss Photo Paper Troubleshooting Lower image gloss directly after printing on HP High Gloss Photo Paper Lower gloss appearance of Page 217 Figure 4: Service Station Assembly You must perform the following Service Calibrations after the NOTE installation of the Service Station Assembly. Page 65: Obtaining Printhead Information HP No.80 Ink Supplies Troubleshooting 5 The front panel displays information on the selected ink cartridge. Hp Designjet 1055cm Plus Troubleshooting HP DesignJets 1050C and 1055CM Printers Service Manual...

Page 136 Service Calibrations CANCEL if you want to cancel the Calibrations Backup. The printer has automatic procedures to hide many nozzle defects. The right-hand edge must be parallel to the white line on the paper entry roller. When removing the Service Station, make sure that you release...

Black cart. Hp Designjet 1050c Plus Parts Hide thumbs Also See for DesignJet 1050C Reference manual - 74 pagesQuick reference manual - 74 pagesUser manual - 286 pages 1 2 3 4 5 6 7 8 Problem Description: Try the following: Corrective Action: Switch the Printer OFF and ON again and wait for the initialization. Tubes Purge 2.

Hp Designjet 1055cm Plus Manual

Close any open door HP DesignJets 1050C and 1055CM Printers Service Manual Make Selection Press Enter... Print Quality How to Use the Print Quality Test What is the Print Quality Test? Hp Designjet 1050c Service Manual I14TLS 5U/LLL- piJilk* ..-J- ►.- ■ ■ •■ : ft-; 1H.L:i HP DesignJets 1050C and 1055CM Printers Service Manual 1-21 Troubleshooting 1-22 HP DesignJets 1050C and 1055CM Printers Service Manual System Hp Designjet 1050c Owners Manual Continuable and Non-Continuable Error Codes Some of the Error Codes are continuable, which means you can press Enter on the front-panel and continue working with the Printer.

Reconnect the power cord and power On the Printer and perform the test again. navigate here Page 108 4 Once the Font selection has been made, the following message will be displayed on the front panel: Postscript asian font selection done. Do not use hand-cut media. Problem solved. Hp Designjet 1055cm Network Configuration

Roller Mark Position 5-13 5. Reply 0 0 dirkster Honor Student Posts: 4 Member Since: ‎07-14-2014 Message 6 of 6 (970 Views) Report Inappropriate Content Re: HP 1050c with Spinjet unit - System error 04C300 004D0000 Page 139 Pen Alignment calibrated. Check This Out Page 156: Solving The Color Alignment Problem Print Quality Below are shown two examples of alignment and misalignment: C6074276 correct Incorrect Solving the Color Alignment Problem 1 Make sure you have

Page 163: Problems With Color-to-color Alignment Print Quality Problems with Color-to-Color Alignment Description of problem When you look at the image you have printed: The colored lines are printing double and Hp Designjet 1055cm Plus Parts Service Utilities... Page 13: Troubleshooting, System Error Codes Color changes when stacking prints done on HP High Gloss Media 1-10 HP-GL/2 color differences in different HP DesignJet Printers 1-11 Scratches on prints done

HP DesignJets 1050C and 1055CM Printers Service Manual System Error Codes Page 8-25.

NOTE The media is causing the problem and NOT the Printer. HP No.80 Ink Supplies Troubleshootingpage 57................................................................................................................................................................ I am assuming I need to replace it? Hp Designjet 1055cm Parts Perform the Electronic Systems Test ⇒...

Page 2 For HP Internal Use Only Warranty ©Copyright Hewlett-Packard The information contained in this Company 1999 document is subject to change without notice. Service Station 5-11 4. Not sure if the Spinjet uses a card in one of the eio slots to work or works thru the parallel port. this contact form Page 100: Entering The Service Utilities Menu Service Tests and Utilities Entering the Service Utilities Menu 1 Once the message "Ready" is displayed on the front-panel, scroll to the "Printer Setup

Replace the EIO Card. Replace the Service Station ⇒ Page 8-8. This problem mainly affects Natural Tracing Paper (NTP), Vellum and HP High Gloss Media. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.