Home > Fuser Error > Hp Lj 8150 Fuser Error

Hp Lj 8150 Fuser Error


Thanks to you guys, I saw two broken D601 solder joints and fixed those by adding a little more solder to the left and right pins. by Mordred on Jun 30, 2005 at 7:51am Add comment Please sign in to comment 0 C4214-69020Cost is over 300.00 at hp.com. Also the formatter has to come out and the cover on that end so that the formatter fan assy can come off. by Anonymous on Jul 20, 2006 at 1:51pm Add comment Please sign in to comment 0 Well, many thanks for the advice.Took out the LVPS and sure enough there was the http://upintheaether.com/fuser-error/hp-8150-fuser-error.php

You can solder it but don't mess with the chip type components - it's the legs of the triacs, generally the center of the three n each triac - that has by oeginc on May 20, 2005 at 1:26pm Add comment Please sign in to comment 0 I too have the same problem and I would like to order the part on unfortunately, a replacement power > supply is about $250-$400. Copyright 2016 Broken Printer.

50.1 Fuser Error On Hp Laserjet 8100 And 8150

All rights reserved. mine was the center leed on Q600! 'll take pictures there is enough space between the board and the leed that I could almost drive a bus through it. Sometimes one of the springs on the either end of the transfer roller clip falls down or comes loose and the transfer roller does not do its job.

Also can not rule out that there is a 20% chance of a DC controller issue also..you need to replace the Low Voltage Power Supply. Turn the board over, about halfway down on the back there will be 2-4 solder joints that have popped. by Stephen on Aug 21, 2006 at 7:45am Add comment Please sign in to comment 0 I am having a problem with a HP 8150N printing extremly light. 50.1 Fuser Error Hp 9050 Your shipping was fast and the parts are great.

Nothing else to offer. 50.1 Fuser Error Hp 4700 HP makes it very easy to setup. I've replaced the fusers and still came up with the error. https://www.marketpoint.com/hp-laserjet-8100-8150-50x-service-error.aspx The error occurs during the initializating.

Are there any components on this power > supply that are common failure points I should specifically check? > Thanks! > Anonymous a b ) Power supply a b α HP 50.1 Fuser Error Hp 9040 by unknown on Aug 21, 2006 at 1:57am Add comment Please sign in to comment 0 Burning smell is not normal.It may be caused by the fuser you put in, or If anything else is plugged in, UNPLUG IT! The solder connections open from heat.

50.1 Fuser Error Hp 4700

The fuser assembly may be hot, allow to cool before removing it from the printer or injury may result. visit Normal >>operations for them sees a lot of trees being killed - they get their >>paper in 2500 sheet boxes without the reams bundled - just 5 reams >>worth in a 50.1 Fuser Error On Hp Laserjet 8100 And 8150 by Mordred on Jul 13, 2005 at 10:58am Add comment Please sign in to comment 0 Increase brightness on Printer Screen Display. 50.1 Fuser Error Hp Laserjet P1102 Now when I power it up, the control panel just blinks, no fans, nothing.

Carefully release the retaining tabs on the plastic panel to the left of the metal back cover by gently pulling the cover to the left while moving both pieces away from http://upintheaether.com/fuser-error/hp-8150-fuser-error-50-1-reset.php I'll take pictures and post them if I can for others. - Andy Z 0 Thank you to all who have posted on this.I had, notice the had, 2 8150's that Check the fuser resistance first to confirm, but most times it will require replacement of the low voltage power supply. Just go around and hit all the suspicious looking ones, mostly the ones that have larger pins. Hp 8150 Low Voltage Power Supply

Are there any components on this power supply that are common failure points I should specifically check? As of right now the LVPS appears to be a viable fix. I had a 50.3 error, rebooted the printer and then got the 50.1 error. navigate here Nevermind the nice shock you may get but it also may fry your new parts.

No, create an account now. 50.1 Fuser Error Hp 5100 So far only one was pulled from service - >>water pipe broke overhead and leaked into the unit all night with >>power applied. If the error continues: 1.

Of course if the previous toner and this one were both new, it is possible the sealing tape was not removed from them.

The most cost effective method of repair is to replace the fuser assembly. by dmzcompute on Sep 19, 2006 at 2:32pm Add comment Please sign in to comment 0 I have this message:- 'Loading Program 1' whenever I switched on the printer HP 8150. Ask for a refurbished one. $189.Nick - nickhill2002 0 If it is the LVPS, most of the errors can be fixed by resoldering the components on the board. Rg5-4357 These heating elements are subject to failure from burned resistive heating paths and fractures of the ceramic substrate material.

Does is mean that your engine is bad when the check engine light is on? Now remove the top cover which is not that hard. Frank measekite, Oct 4, 2005 #17 Advertisements Show Ignored Content Want to reply to this thread or ask your own question? http://upintheaether.com/fuser-error/hp-printer-8150-fuser-error.php In all this time only one has needed any fuses and >that was the AC inlet fuse. > >Since you in the UK use a different model LVPS and fuser for

I checked the DC Controller board. I took the LVPS apart and sure enough the solder on D601 was evaporated. Select Your Printer Model Common To Most Newer HP Laserjet printers HP LJ 8150 50.1 Fuser Error HP LJ 4/4M and HP LJ 4+/4M+/5 •Common to HP Laserjet Printers 50.X FUSER Just a small way of paying back all the good this site has done for me.

Yes the most general thing is maintenance kits especially if cheapo kits (non-OEM) are used, they will generally fail well before 350k but HP kits seem to run into 500k before It may have a lot to do with the vents getting blocked for cooling air as I find all the LVPS units that have this are heavily blocked with crap at Ok it didn't work so it's something else. I assume it's back somewhere near the power cord, or even where the power cord plugs in, right?

I re-soldered triad and put back together.Guess what?No joy! Sorry. In some cases this error can also be caused by a defective power supply or faulty DC controller board, but check the fuser first. by Trip on Feb 1, 2006 at 6:02am Add comment Please sign in to comment 0 Just adding my two cents.

I always have a fuser with me and always the error stays even with the new fuser. Now in the back at the top where the hinge of the top cover is located is one additional screw. Wird geladen... Hinzufügen Möchtest du dieses Video später noch einmal ansehen?

I poked around the power supply a bit, but nothing is > immediately obviously broken. by dmzcompute on Dec 14, 2005 at 8:48pm Add comment Please sign in to comment 0 Also this error is showing up on 5Si and 8000 series printers - LVPS is by msr976 on Dec 5, 2006 at 6:29am Add comment Please sign in to comment 0 Most of the time it is the Low Voltage Power Supply...And HP is providing free If I can't fix something onsite, a paper clip will normally do the trick in certain circumstances.

I have replaced the toner and fuser with known good ones and I am still having the same problem.