Home > Fuser Error > Hp 8100 Fuser Error

Hp 8100 Fuser Error


Certainly not arguing with you, your approach to give the customer a choice but to also provide professional advice is perfect. Other >>common problems is the one listed - 50.1 fuser error, usually caused >>by broken solder joints on the LVPS at the triac connections. 99.9% >>of the time a reflow of Tony[/quote:6fb92d6a7f] You must work on lightly used 5Si, 8000, 8100 and 8150 series machines to say that - I do at least 5 a day for a series of bank mortgage So then I replaced the dc controller board just like the service manual says, but the error is still there. http://upintheaether.com/fuser-error/hp-50-9-fuser-error.php

The error occurs during the initializating. Please wait... Check the pressure roller and gears for signs of wear. Irwin Peckinloomer, Oct 4, 2005 #14 Frank Guest Irwin Peckinloomer wrote: > In article , > says... > >>*TONY DA TIGER IS IN DA BUSINESS* >> > > Therefore he might

50.1 Fuser Error Hp 4700

If the bushings are worn you will typically notice: (1) Metal shavings that fall out as you're checking the unit, and (2) a jerky feeling as you rotate the gears. partsnow.com are few that sell you a refurb on advanced exchange. We're going to go > that route. I try to work >this into the contract/3rd party people's heads but they contnue to >look at cost to buy vs durability/dependabilty.

Power supply is the most common cause. (RG5-4357) Pull the fuser out and check the thermal fuse on top of the fuser and the lamps inside the unit for continuity to Reseat or replace the fuser cable assembly. 3. I took the old fuser to another LaserJet 8150, and it is working fine. Hp 8150 Low Voltage Power Supply To not being in the business and knowing nothing?

In all this time only one has needed any fuses and >>that was the AC inlet fuse. >> >>Since you in the UK use a different model LVPS and fuser for 50.1 Fuser Error Hp Laserjet P1102 I do >>appreciate the info. It was a 5si so they replaced it with a new 8150N. > >Davy I'm not sure of your point but I am aware of the LVPS providing >other than fuser You need to contact a service provider in your area and have him check to see if your model and serial number are covered by the service note.

Frank Frank, Oct 4, 2005 #15 measekite Guest Irwin Peckinloomer wrote: >In article , > says... > > >>*TONY DA TIGER IS IN DA BUSINESS* >> >> >> >Therefore he 50.1 Fuser Error Hp 3600 Could be possible the fuser and LVPS has gone bad at the same time. If you don't have very many problems I >wish HP would hire the same vendor to make new replacements, they >seem to have it right on the 220's. I've seen 500 sheets from tray 2 get used in the time >>I was working on a nearby printer. >> >>Their 5si's are avg 3 mil page counts, the 8150's go

50.1 Fuser Error Hp Laserjet P1102

Anyone know what else can cause this error?? http://fixyourownprinter.com/posts/17513 To not being in the > business and knowing nothing? > Well that one statement clearly points out what a complete moron I > really am. > Clueless and brainless. 50.1 Fuser Error Hp 4700 Side skew of the border especially >on letter where a box is around it like a paper path test sheet is a >bad carrier for the transfer roller so I try 50.1 Fuser Error Hp 6040 by dmzcompute on Oct 29, 2004 at 12:10pm Add comment Please sign in to comment 0 Hi Dewaine, Welcome back to the board.

Open the 2000-sheet input tray transfer door (if installed), tray 1, and the right lower door assembly 4. navigate here Chanarda Murray 6 months ago Thanks very much for this video. Reply 0 Re: hp 8100 fuser error 50 service 10-25-2011 03:20 PM It was the low voltage power supply. and may not be used without advance written permission of PrinterTechs.com, Inc. 50.1 Fuser Error Hp 9050

Note that the fuser is the first part that most commonly will cause the 50 error, and then the DC controller. The remainding 5 for locals were sucessfully repaired >by resoldering. One of HPs rules. Check This Out Die Bewertungsfunktion ist nach Ausleihen des Videos verfügbar.

I haven't heard of anyone that has ordered and gotten one either. 50.1 Fuser Error Hp 9040 The two time I had the error and new fuser did not work it was the ac power unit which fixed it. Wird geladen...

by dmzcompute on Dec 24, 2006 at 6:10pm Add comment Please sign in to comment 0 I have the exact same issue.

Thanks! > >Also, can anyone reccomend a good site on preventive maintence on these >printers? Guest I have an HP LaserJet 8150 which is displaying a 50.1 Fuser error, which I tracked down to the Low Voltage Power Supply's 24V rail being dead. Sign up now! 50.1 Fuser Error Hp 5100 Unfortunately, service contracts were allowed to lapse >>> >>> >>on >> >> >>>these printers and I suspect these printers have been neglected, so >>> >>> >>I >> >> >>>would be interested

Related Products z Fuser Gear Kit hp Laserjet 8100/8150 $12.95 Paper Jam Kit hp Laserjet 8100/8150 $16.95 Fuser Roller Upper hp Laserjet 8100 / 8150 $29.50 z Fuser Locking Levers hp We're a friendly computing community, bustling with knowledgeable members to help solve your tech questions. Edwin AveryRanchDental 6 months ago  Reply Great step by step video! this contact form I found that the problem is the low voltage power supply, it is connected to the fuser and if just changing the furser doesn't work, this is the problem, the book

First, we purchased and received a fuser from you early last week. Also, can anyone reccomend a good site on preventive maintence on these printers? Does anyone actually have the official service note? All rights reserved.

You have replaced everything that would give you the error. Are you sure you go a good ac power unit? Solved! I've had this repair happen in the field on countless occasions.

We've missed you. I rebuild the PIU and outfeed with parts from PartsMart in Georgia rather than buying a whole PIU or outfeed (except for the mortgage office jobs - they buy the parts Maintenance Kit should installed every 350,000 pages (C3914-69001). Thanks again, and keep making these videos.