Home > Fuser Error > Hp 5si 50.1 Error Code

Hp 5si 50.1 Error Code

Contents

Die Bewertungsfunktion ist nach Ausleihen des Videos verfügbar. On LaserJet's 4250, 4350 series you need to wait until you turn the power on and the memory starts counting before you hold the checkmark button. Turn the printer off and allow it to cool down for a minimum of 20 minutes.2. System error 64:04 Firmware error (USB port). http://upintheaether.com/fuser-error/hp-8150-laserjet-error-code-50.php

System error 85:10 Paper-axis shutdown (during the paper advance test). Du kannst diese Einstellung unten ändern. X Description: hp 4000 50.1 is Low Fuser temperature 50.2 is Fuser warm up service 50.3 is High Fuser temperature 50.4 is Low/Bad line voltage (Printer hooked up to UPS) 50.5 Replace cable, AC Power Module to DC Controller, connector J208. (P/N RG1-0912-000.) IIP, IIP+, IIIP Only: 1.

50.1 Fuser Error Hp 4700

HP LASER PRINTERS 3015/3020/3030MFP1. Replace Paper Control PCA (Solenoid/Sensor PCB Assembly). 4. When that did not solve our problem, we purchased a power supply..

Replace Formatter PCA. 69 SERVICE 1. No toner cartridge. 3. Turn the printer on. 4. 50.1 Fuser Error Hp 9040 Replace the fuser ass'y4.

Maybe a cold reset too.. 50.1 Fuser Error On Hp Laserjet 8100 And 8150 System error 81:11 Paper-axis shutdown (during the paper advance test). Paper won't feed properly, misfeeds can occur, and if paper jams inside the fuser it can damage the sensitive heating element in the fuser. The product has experienced an internal hardware error.2.

See error 51. 50.0 Fuser Error For LJ III, IIID, IIIP, IIISi/4Si with 1 MB extra memory, enable page protect. 22 ERROR/ I/O CONFIG ERROR 1. Front Door-open Sensor (PS402) broken or stuck. 2. The maintenance kit message will only go away if you reset or clear the maintenance count.

50.1 Fuser Error On Hp Laserjet 8100 And 8150

Replace both at same time. Defective fuser. 2. 50.1 Fuser Error Hp 4700 Defective fuser. 2. 50.1 Fuser Error Hp Laserjet P1102 Learn more You're viewing YouTube in German.

If You Have Any Problems That You Don't See Or Need Questions Answered You Can Email Me. controller. 5. Bad Paper Input sensor (PS1). 2. Replace the fuser power supply or the low voltage power supply.4. 50.1 Fuser Error Hp 9050

I have alreadycome across this as being the problem and it sounds about right.Everything else works it just produces blank pages. HP Laser-jet 4000 51.1 is Beam detect error and 51.2 is Laser error 52. Replace Laser/Scanning Assembly. 4. Check This Out is between 2925J00000 to 3047J999999. (2-diode to 3-diode upgrade corrects static caused problem.) IIP, IIP+, IIIP Only: 1.

Replace DC Controller PCA. 2. 50.1 Fuser Error Hp 5100 I reseated the fuser (it was hot to touch) cleaned out the printer with compresed air, Powered everything off for 20 min. Took me about an hour to do the repair, including time spent watching the video.

My Account Order Status Wish Lists Gift Certificates View Cart Sign in or Create an account Search Advanced Search | Search Tips Home About Us Contact Us Shipping (hp) Printer Parts

Turn the MFP off, and allow it to cool. 3. DC Controller malfunction. 4. Carefully release the cover around the AC input connector at the lower right of the back cover and slide the right side of the cover slightly forward. 6. 50.0 Fuser Error Hp Laserjet P1108 Thanks again, and keep making these videos.

Replace toner cartridge. 2. If printer is hooked up to uninterruptible power supply or surge protector plug straight in to wall.2. Anmelden Teilen Mehr Melden Möchtest du dieses Video melden? this contact form Replace PostScript ROMs.

X=5 The wrong fuser is installed, or no fuser is install. Check and reseat connector J010 on DC Controller PCA. 3. Reset the maintenance count on HP LaserJet 4100MFP, 4101MFP, Laser 4200, 4300, 4250, 4350 and HP 9000, 9040 and 9050 1. IIISi/4Si 1.

Open the top cover door, and remove 2 screw 3. Reseat the formatter cable in the ECU.3. Remove the 2 screws from the plastic panel to the left of the metal back cover 5. If the error continues: 1.

A fellow printer tech Dear Broken Printer, Posted by Unknown on 27th Feb 2013 Thanks to you I have our 8150DN back up and running. Improperly seated fuser. 2. If a surge protector is being used, remove it. Wird geladen...

c. It just started printing blank pages on Monday. Fuser Error Code 50.1: Low fuser temperature 50.2: Fuser warm-up service 50.3: High fuser temperature 50.4: Faulty fuser 50.5: Inconsistent fuser (verify voltage model) Service Manual Recommended Action Turn the printer No toner cartridge or cartridge not seated. 3.