Home > Fuser Error > Hp 4600 50.2 Error

Hp 4600 50.2 Error

Contents

If using DDR SDRAM for the HP Color LaserJet 4650, make sure it meets specifications and is correctly seated. Parts are thoroughly tested, inspected for damage & defects and guaranteed 100% fully functional. $49.00 HP RM1-2763-000CN Fuser Assembly MFG Part Number: RM1-2763-000CN Condition:Refurbished MFG:HP This HP RM1-2763-000CN Make sure fuser is installed correctly.2. If the display panel on your HP LaserJet printer reads "PERFORM PRINTER MAINTENANCE" your HP LaserJet printer needs a maintenance kit, which includes a fuser unit and separation rollers.

Continue holding the green (Select) button until the Ready, Data, and Attention lights flash once, and then stay on steady. If the message returns, check the memory DIMM in Slot J4 to ensure it is supported memory. Improperly seated fuser. 2. Pull paper by bother corners to remove it. http://www.printertechs.com/printer-troubleshooting/11-50-2-fuser-error

50.2 Fuser Error

HP LASER PRINTER 3300, 33801. Watch the control panel. The control panel will display COLD RESET . Whenever the printer is ready, not busy, and has no pending warning messages, the status message READY is displayed if the printer is online.

alternates with TO CONTINUE PRESS (Select) 49.xxxx PRINTER ERROR 50.X FUSER ERROR for help press the ? 51.XY PRINTER ERROR FOR HELP PRESS ? The control panel will display COLD RESET . If this message persists, contact an HP-authorized service or support provider. 50.0 Fuser Error Hp Laserjet P1102 top 54.7 PRINTER ERROR Description There is a problem with the yellow drum home position sensor.

Note: this message will only appear in the Configuration Menu if the PERFORM USER MAINTENANCE message appears. Turn on the printer. System error 81:01 Paper-axis shutdown. Unscrew the two screws retaining the card in the printer.

Press and release the (Back Arrow). 50.2 Fuser Error Hp 4525 If this message persists, contact an HP-authorized service or support provider. When the memory starts counting, press and hold the green (Select) button. Make sure paper trays are not overfilled.

50.2 Fuser Error Laserjet Pro 400

If this message persists, contact an HP-authorized service or support provider. Watch the control panel. 50.2 Fuser Error Action Turn the printer off and then back on again. 50.2 Fuser Error P4015 Try a different power cord.

Verify that the connection to connector J82 on the DC controller PCA is firmly seated. 6. Release the check button when the Ready, Data, and Attention light are on steady. Watch the control panel. Bad D.C. Fuser Error Hp Printer

The control panel will display SELECT LANGUAGE . Replace engine board. Try a different electrical circuit or outlet. alternates with TO CONTINUE TURN OFF THEN ON 62 NO SYSTEM TO CONTINUE TURN OFF THEN ON 64 PRINTER ERROR FOR HELP PRESS ?

System error 22:10 A problem has been detected with the Ink Supply Station. 50.1 Fuser Error We replace HP LaserJet printer maintenance kits and fuser kits and clear printer maintenance service error message! Press the up arrow (Navigation) button until the message New Maintenance Kit appears on the control panel display. 7.

If a surge protector is being used, remove it.

Defective fuser cable to DC controller. 2. HP LASER PRINTER 9000, 9040, 9050MFP THIS IS FOR ALL ERROR 50.X 1. The control panel will display COLD RESET . 50.3 Fuser Error If this message persists, contact an HP-authorized service or support provider.

Lift the fuser by grasping the fuser housing above the green arrow on the left and right. Power off the printer and unplug the power cord before proceeding with the following steps. Power cycle the product to determine if the error is persistent. 2. Press (Down Arrow) to highlight CALIBRATE NOW or QUICK CALIBRATE NOW .

The printer will perform a cold reset and then continue its power-on sequence. Continue holding the green check button until the Ready, Data, and Attention lights flash once, and then stay on steady.