Home > Fuser Error > Hp 3700n Fuser Error

Hp 3700n Fuser Error

Contents

I believe the power supply could be causing this problem. Some data will be lost. Figure 43: Remove jammed paper Push the metal paper-access plate (duplex pan) up until it locks in place. Watch the control panel. http://upintheaether.com/fuser-error/hp-5si-fuser-error.php

top 10.00.YY SUPPLIES ERROR For help press ? Before initializing NVRAM, print a Configuration page and a supplies status page to gather the following information: Total page count and color page count Transfer kit count Fuser kit count Serial top 68.X PERMANENT STORAGE ERROR SETTING CHANGE FOR HELP PRESS ? If this message persists, contact an HP-authorized service or support provider. http://www.printertechs.com/printer-troubleshooting/409-50-9-fuser-error-hp-color-laserjet-3500-3550-3700

Hp 3600 Fuser

The control panel will display SELECT LANGUAGE . Press (Down Arrow) to highlight CONFIGURE DEVICE . Check for and remove any obstructions in the fuser including the two orange shipping blocks.

Action. Watch the control panel. Action Turn the printer off, and turn it on again. top 54.14 PRINTER ERROR Description There is a problem with the yellow density sensor.

Check for a loose parallel cable connection (disconnect and reconnect the cable at both ends to be sure) and be sure to use a high-quality cable. 50.1 Fuser Error Action Turn the printer off, and turn it on again. Click here to order a maintenance kit with replacement fuserClick here to see fuser installation instructions50.1 Low fuser temperature50.2 Fuser warm-up error *50.3 High fuser temperature50.4 Faulty fuser50.7 Fuser pressure release

Showing results for  Search instead for  Do you mean  or Post new question Question Reply Topic Options Subscribe Mark Topic as New Mark Topic as Read Float this Topic to the

If the message persists, contact an HP-authorized service or support provider. If the 49 error returns, contact an HP-authorized service or support provider. Cold reset the printer: Turn on the printer. If you still have the messages continue with next step.2.

50.1 Fuser Error

Printing cannot continue. http://h30434.www3.hp.com/t5/LaserJet-Printing/3700n-Fuser-Error/td-p/41649 Press (Down Arrow) to highlight CALIBRATE NOW or QUICK CALIBRATE NOW . Hp 3600 Fuser If the message persists, contact HP support.Understanding Control Panel Messages I am an HP employee.Say Thanks by clicking the Kudos Star in the post that helped you.Please mark the post that Office Depot Figure 2: Paper pickup assembly 1 - Paper pickup assembly Check for any loose paper on the right side of the paper pickup assembly, near the white gear.

Use Web Jetadmin software to delete files from the storage device. http://upintheaether.com/fuser-error/hp-50-9-fuser-error.php Press (Select) to select CALIBRATE NOW or QUICK CALIBRATE NOW . To learn more about Amazon Sponsored Products, click here. Press (Select) to print the Configuration page.

The printer will perform a cold reset and then continue its power-on sequence. The control panel will display COLD RESET . Turn the printer off, and turn it on again. Check This Out Remove any excess paper from the input tray.

The control panel will display COLD RESET . Action Lift the top cover. alternates with TO CONTINUE TURN OFF THEN ON Possible printer control panel error message 59.0K 59.3K 59.6K 59.8Y 59.BC 59.0C 59.3C 59.6C 59.90 59.BM 59.0M 59.3M 59.6M 59.9K 59.BY 59.0Y 59.3Y

Verify that all print cartridges, the transfer unit, and the fuser are correctly installed.

The printer will perform a cold reset and then continue its power-on sequence. Press the (Down Arrow) button until PRINT CONFIGURATION is highlighted. To improve print speed and increase memory resources, disable paper jam recovery. Clean the color registration detection sensor above the black print cartridge if the error does not clear.

Action Lift the top cover. Would you like to tell us about a lower price? Action Turn the printer off, and turn it on again. this contact form It has 80% left on supplies page.Thanks Reply 0 Reply 0 0 LaserGuy Teacher Posts: 82 Member Since: ‎02-19-2009 Message 2 of 2 (1,616 Views) Report Inappropriate Content Re: 3700n Fuser

If this message persists, contact an HP-authorized service or support provider. Open up the fuser cover by lifting the green square tab on the right-hand side of the fuser. Reply 0 0 pcwizard Provost Posts: 12,147 Member Since: ‎12-31-2009 Message 4 of 16 (37,220 Views) Report Inappropriate Content Re: 50.7 Fuser Error Message Options Mark as New Bookmark Subscribe Subscribe NOTE: Use the paper path test in the Diagnostics menu to print pages while troubleshooting.

Turn the printer off, and turn it on again. Cold reset the printer. Reseat the EIO card and turn on the printer. When the memory starts counting, press and hold the green (Select) button.

Press (Select). The control panel will display SELECT LANGUAGE . Thank you.Read more0Comment| One person found this helpful. Action Turn the printer off, and turn it on again.

Release the (Select) button when the Ready, Data, and Attention light are on steady. Locate the Jetdirect network card near the rear of the printer's right-hand side. Action Press (Select) to continue. Paper should be stored in the original packaging in a controlled environment.

Reseat or replace the memory in DIMM Slot J1. If the message persists, turn the printer off and then back on again. top 13.01.00 JAM IN TRAY X For help press ?