Hp Error 55
Replace the formatter board. (On the 5si, 8000, 8100 this could be a fuser problem. Twitter: @Ciara_B_HP Reply 0 0 « Message Listing « Previous Topic Next Topic » Related Documents HP Printers - Using HP Diagnostic Tools for HP Printers in WindowsHP Printers - After Error 50 (fuser malfunction) HP II/III series most likely cause is the ac power module is defective. Replace the fan.
HP Error Code:59 - Motor Error Explanation:The printer has a motor error, possibly relating to the main motor, fuser motor, image drum motor or ETC motor. What to do:Update to the latest firmware to rule out this issue. Thank you for the speedy shipment and response. X = Description 4 Printer Fan 7 Duplex Fan 1. http://www.printertechs.com/printer-troubleshooting/hp-error-codes/195-numeric-error-codes-50-59-hp-laserjet
52 Scanner Error Hp Laserjet
On HP II/III and IISi/4Si models check that at least one sensitivity tab is installed on the right side of the toner cartridge. Search the Community Entire ForumThis CategoryThis BoardUsers turn on suggested results Auto-suggest helps you quickly narrow down your search results by suggesting Verify the tab on the cover is not broken. Regards mr lim - fern ale road.
Also verify the configuration through the menus on the printer. X represents the error location and can equal one of the following: 1 = Slot number 1 2 = Slot number 2 3 = Slot number 3 6 = Card in Replace main motor. 59.f0 Error Hp Printer Contact HP support: www.hp.com/go/support 55.0601 DC controller NVRAM data error Turn the printer off, and on again.
Check these items. Paper jams can occur at four stages: pickup, printing, fusing and exit. What to do:Turn off the printer and remove the printer cable (USB or I/O cable), then turn it back on. http://www.advancedlaser-hp-error-codes.com/error_55.htm I will have purchasing call in an order.
HP Error Code:02 - Warming Up Explanation:This is commonly associated with printer cable or driver problems. 52 Scanner Error M521dn Replace if problem persists IIIP/IIP/IIP+ Paper feed problem - check feed/pickup rollers for movement and wear. X description: 1 = Scanner startup error 2 = Scanner rotation error 1. Defective laser scanner assembly.
50.0 Fuser Error
HP 4/4+/5 most likely cause is burned out quartz lamp. http://h30434.www3.hp.com/t5/Desktop-Operating-Systems-and-Recovery/printer-error-55-a/td-p/5303105 Bad tray bin reports.5. 52 Scanner Error Hp Laserjet Occasionally the contact for the micro switch will get bent and will have to be replaced. 50.0 Fuser Error Hp Laserjet P1102 I am new to this and do not want to screw this up.
HP Error Code:80 - Defective Network Card or Formatter Board Explanation:Your printer has a defective accessory of some kind, possibly related to memory, I/O cards or a firmware issue. HP LASER PRINTER 3050, 3052, 3055, 3390, 3392 1. If you think you have received a fake HP Support message, please report it to us by clicking on the blue “Report Inappropriate Content” button above the message. Check the tab on the bottom of the toner cartridge facing you as you open the printer. 50.0 Fuser Error Hp Laserjet P1108
Can the post be marked closed & solved?Thanks, Ciara I am an HP employee.I am speaking for myself and not for HP. ERROR 49.XXXX A critical firmware error has occurred that caused the processor on the formatter to abort the operation. What to do:These faults typically needed assistance from an experienced HP engineer. Different models have slightly different wording for the error, but the troubleshooting tips are generally the same.Common HP Printer Error MessagesMany HP printer error messages are common amongst the range, both
Improper MIO connection - look at pins on formatter MIO connection reseat card. 50.0 Fuser Error Hp Laserjet P1007 Listen for erratic sounding scanner motor. How did we do?
This can generally get you 100 or so more pages.
Event code Description Recommended action 55.0005 Hardware memory error (DC controller) The engine control PCA needs to be replaced. All new models with tray lift problems can often be resolved by checking for obstructions such as paperclips or other objects. Restart printer. 50 Fuser Error Hp Laserjet 3050 Back back to top Error 16 Toner Low Toner cartridge is empty or toner in cartridge is not distributed evenly.
Fans will go into high speed operation during the print cycle. Defective toner cartridge in the Laserjet 4 Plus only. HP Error Code:61 - Formatter , Memory Error Explanation:Your printer either has improperly fitted or bad memory SIMMs or a defective formatter board. Also check for any partially peeled labels, this can be a disaster if they come off inside the printer.
Check the fan connector and make sure that the fan is not blocked. 2. All other printers, replace laser scanner assembly. HP IIP/IIP+/IIIP could be either the laser pca or the scanner motor. Firmware Update - The configuration page lists the firmware version of the product.
Back back to top How did we do? Reseat cables to the laser/ scanner and engine controller. 4. If this doesn't work and replacing the chips still doesn't resolve the problem then you may have to replace the formatter board. Service Error NVRAM full Explanation:The NVRAM is full, meaning some actions can't be processed.
If the error persists, replace the ECU.HP LASER PRINTERS 4200, 4300, 4250, 4350 FOR ERROR CODE 55.X1. May also be formatter. Paper multifeed or wrong size paper being used. Reply 0 Reply 0 0 Everyone's Tags: PT1 View All (1) Shane_R Associate Dean Posts: 7,948 Member Since: 11-28-2011 Message 2 of 16 (54,996 Views) Report Inappropriate Content Re: HP Laserjet
The page containing the error will automatically be reprinted. 1. Defective firmware DIMM. Back back to top How did we do? You may need additional memory. 4L Same thing with to much data or the page is to complex.
Also caused by the density adjusting PCA located behind the density adjusting slide switch. Error 80 Improper MIO connection - look at pins on formatter MIO connection Defective MIO Card - Replace card Defective Formatter Card - Replace card Error 89 The PostScript ROM's have If unresolved, remove all cards/accessories and replace one my one to identify what is at fault. The page containing the error will automatically be reprinted. 2.