Home > Error Codes > Ibm Hard Disk Error Codes

Ibm Hard Disk Error Codes

Contents

See error codes 00151100, 00151200, and 00151300 for action. 00151351 Processor Machine Check Data b Address= xxxx xxxx xxxx xxxx Time stamp=xxxx xxxx xxxx xxxx Additional data for debugging. Remove each I/O expansion card one at a time, restarting the blade server each time, until the problem is isolated - See Turning off the blade serverRemoving an I/O expansion card A valid master Initial Microcode Load record was not found on the diskette. Select your product: 100-14IBD Laptop (ideapad) 100-14IBY Laptop (ideapad) 100-15IBD Laptop (ideapad) 100-15IBY Laptop (ideapad) 100S Chromebook (Lenovo) 100S-11IBY Laptop (ideapad) 100S-14IBR Laptop (ideapad) 110 Touch-15ACL Laptop (ideapad) 110-14IBR Laptop (ideapad) More about the author

Contact your local technical Support Center Search Was this information helpful? This listing, which consists mostly of error codes and sounds that are displayed during POST (Power-On Self-Test) may be of use to users in problem determination. Hot-swap storage drive - See Removing a hot-swap storage drive and Installing a hot-swap storage drive. Run the Configuration/Setup Utility program (Using the Configuration/Setup Utility program), select Load Default Settings and save the settings. http://www.bioscentral.com/misc/ibmdiag.htm

Ibm Error Codes

The problem was, these diagnostic codes were never really documented all that well. OS/2 Trap 2 errors (spurious NMI or adapter parity check error): Replace memory options until fixed; if unsuccessful, replace motherboard. See Solving shared BladeCenter resource problems. (Trained service technician only) Replace the system-board assembly - See Removing the system-board assembly and Installing the system-board assembly. 604 Diskette drive failure. Run the Configuration/Setup Utility program and make sure that interrupt resource settings are correct.

Contact HP If the Hard Drive Test displays an error message and a failure ID code, contact HP using the Contact Support tab at the top of this screen. Ensure that you see ATA HDD0 and that it has a device id next to it (EX: ATA HDD0 HITACHI HTS543232L9SA00) Press F10 to save and exit and then press the Hot-swap storage drive - See Removing a hot-swap storage drive and Installing a hot-swap storage drive. Ibm Checkpoint Codes Unsupported SIMM.

Turn on the computer At the ThinkPad splash screen, press F1 for BIOS Setup Utility. How Many Digits Are In A Mac Address? Replace the following components, one at a time, in the order shown, restarting the blade server each time: I/O expansion card in slot xx - Optional expansion unit (if one is This doesn't help much for a Trap 0002, but for the others, the registers AX, BX, CX, etc are the values in those registers at the time the exception occurred. Remove each I/O expansion card one at a time, restarting the blade server each time, until the problem is isolated.

The IBM ROM IML routine would have detected incompatible incompatible IML record. Parity Error Message Run Configuration. 0129 1200 means that a watchdog timeout occurred. Replace the following components one at a time, in the order shown, restarting the blade server each time: Failed I/O expansion card - See Removing an I/O expansion card andInstalling an Reseat the I/O expansion card in slot xx; then, restart the blade server.

How Many Digits Are In A Mac Address?

If an expansion unit is installed, reseat it. http://www.ibm.com/support/knowledgecenter/STCMML8/com.ibm.storage.ts3500.doc/opg_3584_a69m4bfs0.html It is the NMI (Non-maskable interrupt) for the processor. Ibm Error Codes This is a latching error; once the error is detected, the system will no longer try to move the ROM to RAM until diagnostics (SETUP) are run to clear the error. 162 Configuration Error Ibm Server X3650 The Utility requires access to Windows.

LAN Adapter 3110 ALT LAN NETWORK Time Out Failure -- Replace Alt. my review here Hot-swap storage drive - See Removing a hot-swap storage drive and Installing a hot-swap storage drive. (Trained service technician only) System-board assembly - See Removing the system-board assembly and Installing the DIMMs - See Removing a memory module and Installing a memory module. (Trained service technician only) System-board assembly - See Removing the system-board assembly and Installing the system-board assembly. This page requires Javascript. What Dos Command Do You Use To Erase A Hard Drive And Make It Bootable?

The system BIOS cannot determine what card caused the problem. PS/2 - Interrupt failure PCC - Interrupt controller failure 102 BIOS ROM checksum error. (Try reseating the ROM chips!) PS/2 - Timer failure or Real time clock 64 byte CMOS RAM If you don't find the exact error code you're looking for, try looking for the first few non-zero digits of the code. http://upintheaether.com/error-codes/hp-eio-error-codes.php Clear the system error log and restart the system. 190 (PS/2) System board error 191 (PS/2) Failed 82385 cache test 192 (N51) Lid switch error (Thinkpad) Voltage converter error 193 (PS/2)

Perform a hard drive diagnostic test to verify the condition of the hard disk drive. Ibm Post Error Codes ROM to RAM remap error. The first part of the error code indicates the device that is causing the trouble.

Replace the following components one at a time, in the order shown, restarting the blade server each time: Battery - See Removing the battery and Installing the battery. (Trained service technician

LAN Network Adapter 3115 ALT LAN NETWORK Analog Failure (RF) (adapter not hooked to translator) 3120 ALT LAN NETWORK ROM BIOS Failure 3141 ALT LAN NETWORK Continuous RF Signal Detected 3142 At the ThinkPad splash screen, press F1 for BIOS Setup. LAN Adapter 3109 ALT LAN NETWORK Sync Failure -- Replace Alt. Ibm Post Beep Codes If a password prompt appears, type the correct password.

Thus 200 means the system memory was tested. Test the hard drive for errors. Check that the hard drive is recognized in BIOS, and is properly set up in the startup sequence for ThinkPad G, R, T, X, and Z series systems. http://upintheaether.com/error-codes/ibm-ps-2-error-codes.php Optional expansion unit - See Removing an optional expansion unit.

Replace the following components one at a time, in the order shown, restarting the blade server each time: Failed I/O expansion card - See Removing an I/O expansion card andInstalling an Test the hard drive after performing each step. See the following optional device procedures: I/O expansion card - See Turning off the blade serverRemoving an I/O expansion card and Turning on the blade server.