Home > Error Codes > Ibm Bios Error 1762

Ibm Bios Error 1762

Contents

Run the Configuration/Setup Utility program, make sure that the hard disk drive configuration is correct, and save the settings. By going to bios setup, i saw that there is not any IDE hard disk! Back to top #9 The Jolly Dummkopf The Jolly Dummkopf Topic Starter Members 29 posts OFFLINE Local time:11:01 AM Posted 25 November 2010 - 09:29 PM The floppy I used Thes press F10 to save and exit the Setup Utility progam.GoodluckJeroen. click site

Run the Configuration/Setup Utility program and make sure that interrupt resource settings are correct. Run the Configuration/Setup Utility program (Setup and configuration overview) and make sure that interrupt resource settings are correct. See error code 00151500 to determine which DIMM to replace. 00151710 Completed Hot Spare memory Copy. Make sure that a bootable operating system is installed. Homepage

How Many Digits Are In A Mac Address?

Optional expansion unit - See Removing an optional expansion unit and Installing an optional expansion unit. (Trained service technician only) If the problem remains after all optional devices have been removed, lex681, Dec 8, 2005 #6 Jeanc1 Guest You didnt say how old that Aptiva is ? --- That CMOS battery could be the cause -- less then 5 years old ?? More About Us...

Check the function of the shared BladeCenter unit resources. Replace the following components one at a time, in the order shown, restarting the blade server each time: (Trained service technician only) Microprocessor - See Removing a microprocessor and heat sink Optional expansion unit (if one is installed) - See Removing an optional expansion unit and Installing an optional expansion unit. (Trained service technician only) System-board assembly - See Removing the system-board Ibm Checkpoint Codes Type your password, then press Enter.

Back to top #13 The Jolly Dummkopf The Jolly Dummkopf Topic Starter Members 29 posts OFFLINE Local time:11:01 AM Posted 27 November 2010 - 06:06 PM I'll do that then. 162 Configuration Error Ibm Server X3650 Back to top #8 Eyesee Eyesee Bleepin Teck Shop BC Advisor 3,451 posts OFFLINE Gender:Male Location:In the middle of Kansas Local time:01:01 PM Posted 24 November 2010 - 01:17 PM System board 1962 (Drive does not contain a valid boot sector) Verify that a startable operating system is installed. https://www.ibm.com/support/entry/portal/docdisplay?lndocid=migr-55677 ejaazj, Sep 1, 2007 #7 Advertisements Show Ignored Content Want to reply to this thread or ask your own question?

Hot-swap storage drive - See Removing a hot-swap storage drive and Installing a hot-swap storage drive. (Trained service technician only) System-board assembly - See Removing the system-board assembly and Installing the Parity Error Message This page is rather extensive and will be updated on a regular basis. I've actually tried using three different floppy disks: the first two got me past the F1 screen but gave me the message Non-system disk or disk error. Was your intent just to ensure that your data is inaccessible?

162 Configuration Error Ibm Server X3650

Then we decided to give it to one of the girls at work since they needed one and didn't have the money. The method for reading these codes is pretty straight forward. How Many Digits Are In A Mac Address? CD-ROM drive CD-ROM power cable IDE cable System board Battery 8603 (Pointing device error) Pointing device System board 00012000 (Machine check architecture error) Microprocessor System board 00180300 (No more memory above Ibm Error Codes or is it easier to buy a new one?

Replace the following components, one at a time, in the order shown, restarting the blade server each time: (Trained service technician only) Microprocessor - See Removing a microprocessor and heat sink Replace the following components, one at a time, in the order shown, restarting the blade server each time: I/O expansion card in slot xx - Optional expansion unit (if one is you can find easily in stores. Unsolicited e-mail is not answered. "Me2Ewe" <> wrote in message news:... >I took out the battery for about 4 hours but it still does the same thing. > The jumper does Ibm Post Beep Codes

Thanks for all your help! Replace the following components one at a time, in the order shown, restarting the blade server each time: Battery - See Removing the battery and Installing the battery. (Trained service technician Replace the following components one at a time, in the order shown, restarting the blade server each time: DIMM xx - See Removing a memory module and Installing a memory module. Dont get much call for it anymore Sounds like the system is not seeing the hard drive on the hardware level.

Lenovo Tech support says "don't worry about the error". What Dos Command Do You Use To Erase A Hard Drive And Make It Bootable? Sign up now! If it is the battery where can I get one?

Reseat the I/O expansion card in slot xx; then, restart the blade server.

Optional expansion unit (if one is installed) - See Removing an optional expansion unit and Installing an optional expansion unit. Please select one of the the following options for further assistance: Support forums Submit a technical question Before you call IBM Service Applicable countries and regions Worldwide Back to top Run the Configuration/Setup Utility program (Using the Configuration/Setup Utility program), select Load Default Settings and save the settings. Ibm Post Error Codes Back to top #11 The Jolly Dummkopf The Jolly Dummkopf Topic Starter Members 29 posts OFFLINE Local time:11:01 AM Posted 26 November 2010 - 07:11 PM I was planning on

Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. I cannot get past this screen, because no password works. See Using the Configuration/Setup Utility program. See Using the Configuration/Setup Utility program.

Please re-enable javascript to access full functionality. If there's no SSD then I may send it back - false advertising on Lenovo's part. I have this question too 0 Kudos Reply bigjoet Fanfold Paper Posts: 4 Registered: ‎02-27-2014 Location: new york Message 2 of 6 (4,709 Views) Re: A730 Boot Error1762 message [Edited] Options