Home > Error Codes > Hydro Quip Error Codes

Hydro Quip Error Codes

Contents

Rule number 1 is to always fill the hot tub after a drain down by placing the hose pipe in the filter housing suction fitting (remove filter) this fills the hot If you see water flowing normally on low speed, and the water level is correct, then remove the filter(s) to see if the error code goes away. The current setting for filtration cycle duration will be displayed (60, 120, 180, 480). Support: Freeze Protection on Balboa M7 Systems 125. check my blog

The Heater On Light Indicator will blink on the function panel whenever there is a call for heat and the heater has not yet been powered. In either case, after the water temperature has cooled down, pressing any key on the spaside panel control will restart the system. The cycles will repeat every 24, 12, or 8 hours within a 24 hour period, Starting from the time programmed. Check for proper spa water level and ensure pump is primed.

Hot Tub Error Codes

SUPPORT: Balboa heater stopped working 127. If the pump is a single speed pump, the Pump key is used to turn it on and off. Low speed pump (and air blower if so equipped) will activate to assist in lowering temperature. --- = "Watchdog". If alternating with temp, may be temporary condition.

One sensor has detected 110º F. Do I need compression nuts for air tubings to connect onto air switches? 122. How do I know if my ozonator is working? 39. Vita Spa Error Codes thunderstorms, voltage surges, etc.).

This optional Auxiliary Spa Side Control allows you to control the four basic functions of your spa from a convenient secondary location. CTI Spa Side Error Codes th1/39 = On startup indicates temperature probe problem. Low speed pump (and air blower if so equipped) will activate to assist in lowering temperature.--- = "Watchdog". Salt Water Application 147.

The Spa or Hot Tub Panel Displays: HL, HFL - This indicates that a substantial difference in temperature between sensors has been detected during heating. - This could indicate a flow Hydroquip Spa Systems Support: FLO or 3 blinking dots error code. (Electronic Only) 4. Support: HL displaying on Spaguts Electronic Topside Panel. 9. Contact qualified service technician.

Balboa Hot Tub Error Codes

All trademarks are the property of their respective trademark holders. © Copyright 2005-2016 by Spas2order.com, SpaGuts and New Guts for Old Spas are registered trademarks of Spas2order.com. http://www.spapartsshop.com/spasideandtopsideerrorcodes.aspx Support: Non-Conductive Dielectric Grease is OK to be used on electrical connections 112. Hot Tub Error Codes The Spa or Hot Tub Panel Displays: SL This indicates the system is in sleep mode and can be changed by pressing the up temp. Hydroquip Spa Troubleshooting If the spa water temperature does not seem to be elevated, the HL reading may have been caused by poor water flow or electrical line interference (e.g.

Heater is deactivated. click site Ecn = Spa operating in Economy Mode. What is the purpose of the bathtub heater, and what is the minimum water temperature requirement prior to activating the bath heater? 116. This is a normal spa function; no further action is necessary.When the auxiliary sensor reads around 40F- (actual temperature dependent on specific auxiliary sensor used), the system provides freeze protection. Hydroquip Hq6000

Will your blower work on 50Hz? 145. This is a normal spa function; no further action is necessary.When either sensor reads below 40 degrees F., the system provides freeze protection. Special Instructions for the 2006 SE Vista Silver Spas: In this model the programming is for the newest circulation pumps. http://upintheaether.com/error-codes/ibm-db2-sql-error-codes.php Any sales or technical advise provided by this site or our staff may not be construed to authorize or suggest anything but professional installation.

drops. Marquis Spa Error Codes If flashing by itself, spa is shut down. Support: Wiring information for the (15-350-2180) 48-Frame 2.0HP 220V SD Waterway Pump, 342102A-10. 106.

Please try the request again.

If the water is still hotter than the set temperature, press the blower button (if applicable) to cool the spa.If your spa is not overheating based on physical vessel temperature and Support: SpaGuts VS Series Topside Panels are not responding. 130. This could indicate poor flow or air bubbles in the heater. Gecko Spa Pack Error Codes COL = Cool condition.

Support: Balboa topside displaying ---F 59. One sensor has detected 118º F at heater. HL = High limit switch tripped. http://upintheaether.com/error-codes/hp-eio-error-codes.php Filter Cycle has stopped & "Filter" indicator is Flashing not an error but a feature: either the filter cycle is in a 40min minute time-out to avoid ozonater activation while spa

The third press will turn the pump off or return to a heat or filtration mode (see note). Search within our knowlege base: Technical Support1. PSoH = Pressure switch open with high pump. The low speed pump or circ pump will operate continuously until the temperature rises above 45° F.

Pr = When spa is first actuated, it will go into Priming Mode. The first press of the Light key will turn the light on. hot = Overheating, water over 112° F. Support: ColorGlo Sparkler not working properly. 11.

Support: What is the Purple cord for or how to connect the purple blower cord to an exisitng blower? 25.